manualshive.com logo in svg

Transmeta Crusoe TM5500, Руководство по проектированию систем

Поделиться
Скачать
Transmeta Crusoe TM5500 Скачать руководство пользователя страница 120

July 17, 2002

120

System Design Checklists

PCI Checklist   

Item

Description

Status

1.

All the PCI REQ and GNT signals must have pull-ups to V3_3 (IOVDD).

2.

All IDSEL series resistors should be 100 

Ω

.

3.

The PCI LOCK# pin on the processor should be pulled up to 3.3 V switched and not 
connected to anything else. TM5500/TM5800 processors do not support locked PCI 
cycles. All other PCI LOCK# pins in the system should be connected together and pulled 
up. 

4.

No PCI signal should rise above 3.3 V because the processor is not 5 V tolerant. If the 
design contains any components that drive 5 V PCI signals, a high-speed bidirectional 
level-translator is needed at the processor to clamp it to 3.3 V. Such a translator is also 
needed if a PCI edge connector is present that is keyed for 5 V.

Serial Bus Checklist   

Item

Description

Status

1.

The SMBus from the southbridge should not be connected to the Serial Debug Bus (i.e. 
pins SD_SCLK and SD_SDATA). The Serial Debug Bus must be connected to the 
Transmeta debug connector and be pulled up to V3_3 (IOVDD).

2.

If the Code Morphing software serial ROM is supported, the write protection PLD should 
be implemented. Check for the following:
•

The pull-up on CS# should be at the PLD input and not its output. The processor tri-
states the PLD input during Deep Sleep, but the PLD always drives the output.

•

The latest reference design pinout should be supported. The write protect signal 
should connect to pin 2 of the DIP/TSOP or pin 3 of the PLCC. The CS# signal should 
connect to pins 4 and 5 on the DIP/TSOP and pins 5 and 6 on the PLCC.

•

None of the pins are 5 V tolerant, so the signal driving the write protect line should 
have a 3.3 V swing.

•

The PLD should be a 3.3 V part with a feature to reduce power consumption when 
inputs are not toggling.

•

All unused inputs and tri-stated outputs should be connected to ground. Pins 18, 19, 
and 23 on the DIP/TSOP and pins 20, 21, and 27 on the PLCC should be no-
connected. 

3.

All new designs must include a mode-bit ROM circuit. For older system designs that did 
not provide mode bit ROM support, a strapping resistor should be present on the mode bit 
ROM data line (i.e. pin CFG_SDATA) to support each applicable boot option below:
•

Boot from serial Code Morphing software ROM: 10 K

Ω

 pull-up to 3.3 V switched.

•

Boot from parallel ROM: 10 K

Ω

 pull-down.

4.

The debug connector should be wired properly to both the mode-bit ROM and serial Code 
Morphing software ROM:
•

Series resistors (220 

Ω

 each) on all the signals between the processor (or PLD) and 

the ROMs.

•

No series resistor on all the signals between the debug connector and the ROMs.

•

Correct pinout on the debug connector. The most common mistakes are reversing 
the pin order and swapping SROM_CS[1:0]#. On the vertical connector, pin 1 is 
RNMI. On the right angle connector, pin 1 is GND. SROM_CS1# should be on pin 9, 
and SROM_CS0# should be on pin 10.

5.

If the serial Code Morphing software ROM is implemented, the 28-pin Atmel part should 
be used. The 32-pin Atmel part and the Macronix part have both been discontinued.

Содержание Crusoe TM5500



































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды