Trane RTHD series Скачать руководство пользователя | Manualshive

Страница: 91 / 150

background image

Operator Interface Controls

RTHD-SVX02H-EN 91

•

Year

•

Hour

•

Minute

•

AM/PM

To change the date or time:
1. Touch the square presenting the attribute you want

to change. The square becomes highlighted.

2. Touch the up or down arrow key on the screen until

the your desired selection appears. Repeat the pro-
cess for any other attributes you want to change.

3. Touch Save to confirm your selection and return to

the Settings screen.

Cleaning the Display

On the Settings screen, touch Clean Display to disable
the Tracer AdaptiView display screen for 15seconds so
that you can clean the screen without it responding to
touch. During this time, thescreen is black with a num-
ber in the center that counts down the seconds. After 15
seconds, theSettings screen re-appears.

Figure 61. Countdown screen

Security Settings

If security if enabled, the Tracer AdaptiView display
requires that you log in with a four-digit security PIN to
make settting changes that are protected by security. This
feature prevents unauthorized personnel from doing so.
There are two levels of security, each allowing specific
changes to be made.
You can view all data without logging in. The log-in
screen appears only when you try to change a setting
that is protected by security, or when you touch the Log
in button from the Settings screen.

Disabling/Enabling Security

The Tracer AdaptiView display gives you the ability to
disable or enable the security feature that allows a user
to log in and log out.
To disable security, you must be logged in:
1. From the Settings screen, touch the Security button.

The Security screen appears (

Figure 62

).

Note:

If you are logged out, the Log in screen appears.

2. Touch the Disable button. The button becomes shad-

ed.

3. Touch Save. The Settings screen appears with only

the Security button visible. The Log in/Logoutbutton
is gone.

To enable security:
1. From the Settings screen, touch the Security button.

The Security screen appears (

Figure 62

).

2. Touch the Enable button. The button becomes shad-

ed.

3. Touch Save. The Settings screen appears with a Log

out button, in addition to the Security button.

Figure 62. Security screen

Figure 63. Security screen

«
...
89
90
91
92
93
...
»

Содержание RTHD series























































































































































Отзывы:

Нет отзывов

Похожие инструкции для RTHD series

Бренд: GardenBeaut Страницы: 20

Бренд: Skope Страницы: 57

MILLENNIUM YCAL0043SC

Бренд: York Страницы: 133

Бренд: Troy-Bilt Страницы: 4

Бренд: Troy-Bilt Страницы: 28

Бренд: Troy-Bilt Страницы: 19

Бренд: EarthQuake Страницы: 36

Бренд: Garland Страницы: 136

Бренд: Farmi Forest Страницы: 128

Бренд: Clint Страницы: 36

Бренд: Clint Страницы: 28

Бренд: Thermo Страницы: 51

Бренд: Daikin Страницы: 16

Бренд: Hansa Страницы: 30

Бренд: Hansa Страницы: 25

Hyperchill ICE076

Бренд: Parker Hiross Страницы: 172

Бренд: FarmBoy Страницы: 65

Бренд: Weed Eater Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды