Trane RTHD series Скачать руководство пользователя страница 118

Страница: 118 / 150

Diagnostics

118

RTHD-SVX02H-EN

Table 35. Diagnostics Table

Hex

Code

Diagnostic Name

and Source

Severity

Persistence Criteria

Reset

Level

3D7

Transition Complete

Input Opened

Immediate

Latch

The Transition Complete input is open with the compressor motor

running after a successful completion of transition. This is active

only for all electromechanical starters

Local

3D5

Transition Complete

Input Shorted

Immediate

Latch

The Transition Complete input is shorted before the compressor

was started. This is active for all electromechanical starters.

Local

Under Voltage

Normal

Non Latch

a. Average of all monitored Line voltages below - 10% of nomi-

nal or the Under/Overvoltage transformer( s) are not connected.

[Must hold = - 10 % of nominal. Must trip = - 15 % of nominal.

Reset differential = min. of 2% and max. of 4%. Time to trip =

min. of 1 min. and max. of 5 min.) Design: Nom. trip: 60 sec-

onds at less than 87.5%, + or - 2.8% at 200V or + or - 1.8% at

575V, Auto Reset at 90% or greater.

Remote

6B6

Heat recovery tank

temperature sensor

Alarm

Latch

Bad Sensor or LLID

Remote

6B6

Heat recovery outlet

temperature sensor

Warning

Latch

Bad Sensor or LLID

Remote

6B6

Heat recovery water

inlet temperature

sensor

Warning

Latch

Bad Sensor or LLID

Remote

6B6

External heat re-

covery temperature

setting input

Warning

Non Latch

Bad Sensor or LLID

Remote

6B6

Heat recovery flow

delay

Alarm

Non Latch

The water in the heat recovery pipeline cannot be proved to

be flowing in 20 minutes after the heat recovery pump relay is

added. The heat recovery pump will be ordered to stop when

the heat recovery line detects the flow of water and the alarm is

cleared.

Remote

6B6

The heat recovery

flow is short

Immediate

Non Latch

The input disconnection of the flow of the heat recovery pipeline

is more than 6 seconds after confirming the flow. The compressor

is automatically cleared after 7 seconds.

Remote

6B6

Undesired flow -

main condenser

Warning

Non Latch

When the main condenser is ordered to shut down, it will con-

tinue to monitor the presence of water. Once the water flow is

detected, the alarm will be automatically cleared.

Remote

6B6

Undesired flow - heat

recovery condenser

Warning

Non Latch

When the heat recovery condenser is ordered to be shut down

for 180 days, it will continue to monitor the presence of water.

Once the water flow is detected, the alarm will be automatically

cleared.

Remote

6B6

No communication:

heat recovery tank

temperature

Alarm

Latch

Continuous communication between M P and functional ID was

interrupted for 35 to 40 seconds.

Remote

6B6

No communication:

heat recovery outlet

temperature

Warning

Latch

Continuous communication between M P and functional ID was

interrupted for 35 to 40 seconds.

Remote

6B6

No communication:

heat recovery water

inlet temperature

Warning

Latch

Continuous communication between M P and functional ID was

interrupted for 35 to 40 seconds.

Remote

6B6

No communication:

heat recovery flow

switch

Alarm

Latch

Continuous communication between M P and functional ID was

interrupted for 35 to 40 seconds.

Remote

6B6

No communication:

heat back pump

Warning

Latch

Continuous communication between M P and functional ID was

interrupted for 35 to 40 seconds.

Remote

6B6

No communication:

external heat recov-

ery Settings

Warning

Latch

Continuous communication between M P and functional ID was

interrupted for 35 to 40 seconds.

Remote

6B6

No communication:

external heat recov-

ery command

Warning

Latch

Continuous communication between M P and functional ID was

interrupted for 35 to 40 seconds.

Remote

Содержание RTHD series






















































































































































Результаты поиска

Содержание RTHD series

Отзывы:

Бренды по названию

Популярные бренды

Trane RTHD series, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание RTHD series

Отзывы:

Бренды по названию

Популярные бренды