Trane RTHD series Скачать руководство пользователя

Страница: 114 / 150

Diagnostics

114

RTHD-SVX02H-EN

Table 35. Diagnostics Table

Hex

Code

Diagnostic Name

and Source

Severity

Persistence Criteria

Reset

Level

Evaporator

Leaving Water

Temperature

Sensor

Normal

Latch

Bad Sensor or LLID

Remote

27D

Evaporator Liquid

Level Sensor

Normal

Latch

Bad Sensor or LLID

Remote

5BA

Evaporator Refriger-

ant

Pressure

Transducer

Normal

Latch

Bad Sensor or LLID

Remote

Evaporator Water

Flow Lost

Immediate

NonLatch

The chilled water flow proof input was open for more than 6-10

contiguous seconds after flow had been proven. The pump com

mand status will not be effected. 6-10 seconds of contiguous flow

shall clear this diagnostic. Even though the pump may be com-

manded to run in the STOP modes (pump off delay time), this

diagnostic shall not be called out in the STOP modes.

Remote

384

Evaporator Water

Flow Overdue

Normal

NonLatch

Evaporator water flow was not proven within 20 minutes of the

Chilled water pump relay being energized. The Evap pump com-

mand status will not be effected.

Remote

5C4

Excessive Loss of

Comm

Immediate

Latch

Loss of comm with 20% or more of the llids configured for the

system has been detected. This diagnostic will suppress the

callout of all subsequent comm loss diagnostics. Check power

supply(s) and power disconnects - troubleshoot LLIDS buss using

TechView

Remote

4C4

External Base Load-

ing Setpoint

Info and Spe-

cial Action

NonLatch

a. Not “Enabled”: no diagnostics. b. “Enabled “: Out- Of-Range

Low or Hi or bad LLID, set diagnostic, default BLS to next level of

priority (e.g. Front Panel SetPoint. This Info diagnostic will auto-

matically reset if the input returns to the normal range.

Remote

External Chilled Wa-

ter Setpoint

Info

NonLatch

a. Function Not “Enabled”: no diagnostics. b. “Enabled “: Out-Of-

Range Low or Hi or bad LLID, set diagnostic, default CWS to next

level of priority (e.g. Front Panel SetPoint). This Info diagnostic

will automatically reset if the input returns to the normal range.

Remote

External Current

Limit Setpoint

Info

NonLatch

a. Not “Enabled”: no diagnostics. b. “Enabled “: Out- Of-Range

Low or Hi or bad LLID, set diagnostic, default CLS to next level of

priority (e.g. Front Panel SetPoint. This Info diagnostic will auto-

matically reset if the input returns to the normal range.

Remote

1C2

High Compressor

Discharge Tempera-

ture

Immediate

Latch

The compressor discharge temperature exceeded 190°F. This

diagnostic will be suppressed if it occurs during the compressor

run-unload period or after the compressor has stopped, but a run

unload will be terminated early as a result. Note: As part of the

Compressor High Temperature Limit Mode (aka Minimum Capac-

ity Limit), the compressor shall be forced loaded as the filtered

discharge temperature nears this trip-point.

Remote

1C6

High Differential

Refrigerant Pressure

Normal

Latch

a. The system differential pressure was above 160 Psid- trip im-

mediately (normal shutdown) B The diff pressure was above 152

Psid - trip in 1 hour

Remote

584

High Evaporator

Liquid Level

Normal

Latch

The liquid level sensor is seen to be at or near its high end of

range for 80 contiguous minutes while the compressor is running.

(The diagnostic timer will hold, but not clear when the circuit is

off). Design: 80% or more of bit count corresponding to +21.2

mm or more liquid level for 80 minutes)

Remote

6B8

High Evaporator

Refrigerant Pressure

Immediate

and Special

Action

NonLatch

The evaporator refrigerant pressure has risen above 190 psig.

The evaporator water pump relay will be de-energized to stop the

pump regardless of why the pump is running. The diagnostic will

auto reset and the pump will return to normal control when the

evaporator pressures falls below 185 psig. This diagnostic must

shutdown the chiller if it is running.

Local

High Pressure Cutout Immediate

Latch

A high pressure cutout was detected; C.O. on rise @ 180 psig,

reset @ 135 psig (+/-5 psi on switching tolerance) Note: Pres-

sure relief valve is 200 Psig +- 2% trip at 315 ± 5 psi. Note:

Other diagnostics that may occur as an expected consequence of

the HPC trip will be suppressed from annunciation. These include

Phase Loss, Power Loss, and Transition Complete Input Open.

Local

1C6

High Refrigerant

Pressure Ratio

Immediate

Latch

The system pressure ratio exceeded 5.61 for 1 contiguous min-

ute. This pressure ratio is a fundamental limitation of the com-

pressor. The pressure ratio is defined as Pcond (abs)/Pevap(abs).

Remote

59C

Loss of Oil at Com-

pressor (Running)

Immediate

Latch

In running modes , Oil Loss Level Sensor detects lack of oil in the

oil tank feeding the compressor (distinguishing a liquid flow from

a vapor flow)

Local

Содержание RTHD series






















































































































































Результаты поиска

Содержание RTHD series

Отзывы:

Похожие инструкции для RTHD series

Бренды по названию

Популярные бренды

Trane RTHD series, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание RTHD series

Отзывы:

Похожие инструкции для RTHD series

Бренды по названию

Популярные бренды