manualshive.com logo in svg

Trane RTHD series, Установка, эксплуатация и обслуживание

Поделиться
Скачать
Trane RTHD series Скачать руководство пользователя страница 3

RTHD-SVX02H-EN 3

Contents

Warnings, Cautions and Notices ......................2
General Information ..........................................7

Unit Identification - Nameplates .................... 7

Figure 1.  Typical Unit Nameplate .................... 7

Unit Nameplates .............................................7

Unit Inspection ................................................ 7

Inspection Checklist ........................................7
Loose Parts Inventory .....................................7

Unit Description ............................................... 8

Model Number Coding System .....................8

Unit Model Number ........................................ 8

Table 1.  Model Number .................................. 8

Model Number (located on compressor 

nameplate) ......................................................12

Table 2.  Compressor Model Number .......... 12
Figure 2.  Component Location for Typical 
RTHD Unit  ........................................................ 12
Figure 3.  Component Location for Typical 
RTHD Unit (Back View) .................................... 13
Figure 4.  Component Location for Typical 
RTHD Total Heat Reclaim Unit ......................... 14
Figure 5.  Component Location for Typical 
RTHD Total Heat Reclaim Unit (Back View) ..... 15
Figure 6.  Component Location for Typical 
RTHD Partial Heat Reclaim Unit ...................... 16
Figure 7.  Component Location for Typical 
RTHD Partial Heat Reclaim Unit (Back View) .. 17

Installation Overview .....................................17

Table 3.  Installation Responsibility Chart for 
RTHD  Units ...................................................... 18
Table 4.  General Data ....................................19
Table 5.  General Data ................................... 20
Table 6.  General Data ................................... 21
Table 7.  General Data ................................... 22
Table 8.  General Data ................................... 23
Table 9.  General Data ................................... 24

Installation Mechanical ...................................25

Storage ........................................................... 25
Location Requirements ................................. 25

Noise Considerations ...................................25
Foundation ....................................................25
Vibration Eliminators ....................................25
Clearances .....................................................25

Figure 8.  Recommended Operating and Ser-
vice Clearances ................................................ 26

Ventilation ......................................................27
Water Drainage .............................................27
Access Restrictions .......................................27
Moving and Rigging .....................................27

Figure 9.  Unit Weights and Dimensions for 
Rigging 28
Table 10.  Unit Weight (lb(kg)) ........................ 29
Table 11.  Center of Gravity(in(mm)) .............. 30

Lifting Procedure ...........................................31

Table 12.  Rigging ............................................ 31
Figure 10. Lifting the Unit ................................ 33

Alternate Moving Method ............................33
Isolation Pads ................................................33
Placement Neoprene Isolator Installation 

(optional) .......................................................34

Figure 11. Isolator Pad Placement................... 34
Figure 12. Oil Separator with Shipping Bracket 
and Compressor Shipping Spacer ................. 35

Unit Leveling .................................................35

Water Piping .................................................. 35

Piping Connections .......................................35
Reversing Water Boxes .................................35

Figure 13. Condenser and Evaporator Water 
Connections -BBB ............................................ 36
Figure 14. Condenser and Evaporator Water 
Connections -BCD/CCD ................................... 37
Figure 15. Condenser and Evaporator Water 
Connections - CEF ............................................ 38
Figure 16. Condenser and Evaporator Water 
Connections - CDE/DDE/EDE ........................... 39
Figure 17. Condenser and Evaporator Water 
Connections – CFF/DFF/EFF ............................ 40
Figure 18. Condenser and Evaporator Water 
Connections - CGG/DGG/EGG ........................ 41
Figure 19. Condenser and Evaporator Water 
Connections - BCH ........................................... 42
Figure 20. Condenser and Evaporator Water 
Connections - CEJ ............................................ 43
Figure 21. Condenser and Evaporator Water 
Connections - CFJ/DFJ ..................................... 44
Figure 22. Condenser and Evaporator Water 
Connections - DGK/EGK .................................. 45
Figure 23. Condenser and Evaporator Water 

Содержание RTHD series























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды