manualshive.com logo in svg

Trane RTHD series, Установка, эксплуатация и обслуживание


Поделиться
Скачать
background image

General Information

18 

RTHD-SVX02H-EN

Table 3.  Installation Responsibility Chart for RTHD  Units

Requirement

Trane-supplied,

Trane-installed

Trane-supplied,

Field-installed

Field-supplied,

Field-installed

• 

Rigging

• 

Safety chains

• 

Clevis connectors - Lifting beam

• 

Isolation

• 

Isolation pads

• 

Elastomeric Isolators (option)

• 

Isolation pads

• 

Elastomeric Isolators (option)

• 

Electrical

• 

Circuit breakers or non-fused 

disconnects (optional)

• 

Unit-mounted starter

• 

Circuit breaker or non-fused dis-

connect handle

• 

Temperature sensor (optional 

outdoor air)

•  Flow switches (may be fieldsu

-

plied)

• 

Condenser water regulating valve 

controller (optional: may be fiel

-

supplied)

• 

Circuit breakers or fusible discon-

nects (optional)

• 

Terminal lugs

• 

Ground connection(s)

• 

Jumper bars

• 

BAS wiring (optional)

• 

IPC wiring

• 

Control voltage wiring

• 

High condenser pressure interlock 

wiring

• 

Chilled water pump contactor and 

wiring

• 

Condenser water pump contactor 

and wiring 

• 

Optional relays and wiring

• 

Water piping

•  Flow switches (may be fieldsup

-

plied)

• 

Condenser water regulating valve 

controller (optional: may be field

-

supplied)

• 

Thermometers

•  Water flow pressure gauges
• 

Isolation and balancing valves water 

piping

• 

Vents and drain valves

• 

Pressure relief valves (for water 

boxes as required)

• 

Pressure Relief

• 

Relief valves

•  Vent line and flexible connector

• 

Insulation

• 

Insulation (optional)

• 

Insulation

Refer to the Installation Mechanical and Installation 
Electrical sections of this manual for detailed installation 
instructions. 

• 

Locate and maintain the loose parts, e.g. isolators, 
temperature sensors, flow sensors or other facto-
ry-ordered, field-installed options, for installation, as 
required. Loose parts are located in the starter/con-
trol panel. 

• 

Install the unit on a foundation with flat support 
surfaces, level within 1/4” (6.35 mm) and of sufficient 
strength to support concentrated loading. Place the 
manufacturer-supplied isolation pad assemblies un-
der the unit. 

• 

Install the unit per the instructions outlined in the 
Mechanical Installation section. 

• 

Complete all water piping and electrical connections.

Note: 

Field piping must be arranged and supported 
to avoid stress on the equipment. It is strongly 
recommended that the piping contractor provide 
at least 3 feet (914 mm) of clearance between the 
pre-installation piping and the planned location 
of the unit. This will allow for proper fit-up upon 
arrival of the unit at the installation site. All nec-
essary piping adjustments can be made at that 
time. Refer to the current engineering bulletin for 
further details on installation. 

• 

Where specified, supply and install valves in the wa-
ter piping upstream and downstream of the evapora-
tor and condenser water boxes, to isolate the shells 
for maintenance and to balance/trim the system. 

• 

Supply and install condenser water control valve(s) 
per Trane Engineering Bulletin -Water Cooled Series 
R® Condenser Water Contol. 

• 

Supply and install flow switches or equivalent de-
vices in both the chilled water and condenser water 
piping. Interlock each switch with the proper pump 
starter and UC800, to ensure that the unit can only 
operate when water flow is established. 

• 

Supply and install taps for thermometers and pres-
sure gauges in the water piping, adjacent to the inlet 
and outlet connections of both the evaporator and 
the condenser. 

• 

Supply and install drain valves on each water box. 

• 

Supply and install vent cocks on each water box. 

• 

Where specified, supply and install strainers ahead 
of all pumps and automatic modulating valves. 

• 

Supply and install refrigerant pressure relief piping 
from the pressure relief to the atmosphere. 

• 

If necessary, supply enough HCFC-134 refrigerant 
and dry nitrogen (75 psig) for pressure testing. 

• 

Start the unit under supervision of a qualified service 

Содержание RTHD series























































































































































Отзывы:

Нет отзывов

Похожие инструкции для RTHD series

BAC RC Series Operation & Maintenance Manual preview
RC Series
Бренд: BAC Страницы: 44
Daikin UAA-ST3M Installation & Maintenance Manual preview
UAA-ST3M
Бренд: Daikin Страницы: 45
Daikin SEHVX20BAW Installation And Operation Manual preview
SEHVX20BAW
Бренд: Daikin Страницы: 52
Daikin WMC Installation, Operation And Maintenance Manual preview
WMC
Бренд: Daikin Страницы: 68
Meccanica Benassi RL 7 2+1 User Manual preview
RL 7 2+1
Бренд: Meccanica Benassi Страницы: 14
Daikin Navigator WWV Installation, Operation And Maintenance Manual preview
Navigator WWV
Бренд: Daikin Страницы: 52
Haden 200037 Instruction Manual preview
200037
Бренд: Haden Страницы: 16
PowerTek 727 Operation & Maintenance Manual preview
727
Бренд: PowerTek Страницы: 7
The Handy 193820002 Instruction Manual preview
193820002
Бренд: The Handy Страницы: 24
Carrier 16DF013 Installation Instructions Manual preview
16DF013
Бренд: Carrier Страницы: 12
AIREDALE DeltaChill Technical Manual preview
DeltaChill
Бренд: AIREDALE Страницы: 302
Weed Eater 2000T Instruction Manual preview
2000T
Бренд: Weed Eater Страницы: 21
Weed Eater WER500A Owner'S Manual preview
WER500A
Бренд: Weed Eater Страницы: 28
Weed Eater HDF550A Owner'S Manual preview
HDF550A
Бренд: Weed Eater Страницы: 24
Weed Eater 164849 Owner'S Manual preview
164849
Бренд: Weed Eater Страницы: 24
Weed Eater 186100 Owner'S Manual preview
186100
Бренд: Weed Eater Страницы: 28
Nakayama MB2100 Manual preview
MB2100
Бренд: Nakayama Страницы: 62
Häfele HC-M48G Instruction Manual preview
HC-M48G
Бренд: Häfele Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды