manualshive.com logo in svg

Trane RTHD series, Установка, эксплуатация и обслуживание

Поделиться
Скачать
Trane RTHD series Скачать руководство пользователя страница 65

RTHD-SVX02H-EN 65

Installation Electrical

General Recommendations

For proper electrical component operation, do not locate 
the unit in areas exposed to dust, dirt, corrosive fumes, 
or excessive humidity. If any of these conditions exist, 
corrective action must be taken.

 

D

WARNING

Hazardous Voltage!

Disconnect all electric power, including remote dis-

connects and discharge all motor start/run capacitors 

before servicing. Follow proper lockout/tagout pro-

cedures to ensure the power cannot be inadvertently 

energized. Verify with an appropriate voltmeter that 

all capacitors have discharged. Failure to disconnect 

power and discharge capacitors before servicing could 

result in death or serious injury.

All wiring must comply with local and National Electric 
Codes. Minimum circuit ampacities and other unit elec-
trical data is on the unit nameplate. See the unit order 
specifications for actual electrical data. Specific electrical 
schematics and connection diagrams are shipped with 
the unit.
Typical wiring diagrams are in the back of this manual.

 

D

CAUTION

Use Copper Conductors Only!

Unit terminals are not designed to accept other types 

of conductors. Failure to use copper conductors may 

result in equipment damage.

Do not allow conduit to interfere with other components, 

structural members or equipment. All conduit must be 
long enough to allow compressor and starter removal.

Note: 

To prevent control malfunctions, do not run low 
voltage wiring (<30V) in conduit with conductors 
carrying more than 30 volts.

Power Supply Wiring

Model RTHD are designed according to NEC Article 310-
15; therefore, all power supply wiring must be sized and 
selected accordingly by the project engineer.
For a complete discussion on the use of conductors, see 
Trane Engineering Bulletin EB-MSCR-40.
Refer to Trane Engineering Bulletin CTV-EB-93 for power 
wire sizing.

Water Pump Power Supply

Provide power supply wiring with fused disconnect for 
both the chilled water and condenser water pumps.

Electrical Panel Power Supply

Power supply wiring instructions for the starter/control 
panel are:
1.  Run line voltage wiring in conduit to access open-

ing(s) on starter/control panel or pull-box. See CTV-
EB-93 for wire sizing and selection information and 
refer to 

Table 18

 that show typical electrical connec-

tion sizes and locations. Always refer to submittal 
information for your actual unit specifications.

Table 18. Wire Selection Chart for Starter Panels

Min. Wire

Size Copper

(75°C)

Supply Leads for All Starters (0 - 2000 Volts)
1 Conduit

3 Wire

1 Conduit

6 Wire

1 Conduit

9 Wire

2 Conduit

6 Wire

2 Conduit

12 Wire

3 Conduit

9 Wire

4 Conduit

12 Wire

8

40

*

*

*

*

*

*

6

52

*

*

*

*

*

*

4

68

*

*

*

*

*

*

3

60

*

*

*

*

*

*

2

92

*

*

*

*

*

*

1

104

*

*

*

*

*

*

0

120

192

252

360

384

360

480

00

140

224

294

420

448

420

560

000

160

256

336

480

512

480

640

0000

184

294

386

552

589

552

736

250

204

326

428

612

653

612

816

300

228

356

479

684

730

684

912

350

248

397

521

744

794

744

992

400

268

429

563

804

858

804

1072

500

304

486

638

912

973

912

1216

Conductors to the starter and motor connected in parallel (electrically joined at both ends to form a single conductor) must be sized 0 (1/0) 

or larger per NEC 310-4. Each phase must be equally represented in each conduit.

Содержание RTHD series























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды