background image

© 2012 Trane   All rights reserved

 RT-SVX39B-EN

Warnings, Cautions and Notices

Warnings, Cautions and Notices.

Note that warnings, 

cautions and notices appear at appropriate intervals 
throughout this manual. Warnings are provide to alert 
installing contractors to potential hazards that could result 
in death or personal injury. Cautions are designed to alert 
personnel to hazardous situations that could result in 
personal injury, while notices indicate a situation that 
could result in equipment or property-damage-only 
accidents.

Your personal safety and the proper operation of this 
machine depend upon the strict observance of these 
precautions.

Read this manual thoroughly before operating or servicing 
this unit.

Important
Environmental Concerns!

Scientific research has shown that certain man-made 
chemicals can affect the earth’s naturally occurring 
stratospheric ozone layer when released to the 
atmosphere. In particular, several of the identified 
chemicals that may affect the ozone layer are refrigerants 
that contain Chlorine, Fluorine and Carbon (CFCs) and 
those containing Hydrogen, Chlorine, Fluorine and 
Carbon (HCFCs). Not all refrigerants containing these 
compounds have the same potential impact to the 
environment. Trane advocates the responsible handling of 
all refrigerants-including industry replacements for CFCs 
such as HCFCs and HFCs.

Responsible Refrigerant Practices!

Trane believes that responsible refrigerant practices are 
important to the environment, our customers, and the air 
conditioning industry. All technicians who handle 
refrigerants must be certified. The Federal Clean Air Act 
(Section 608) sets forth the requirements for handling, 
reclaiming, recovering and recycling of certain 
refrigerants and the equipment that is used in these 
service procedures. In addition, some states or 
municipalities may have additional requirements that 

must also be adhered to for responsible management of 
refrigerants. Know the applicable laws and follow them.

Revision Summary

RT-SVX39B-EN (11 September 2012)

MERV 8 filter with filter removal tool

Stainless steel drain pan, condensate overflow switch

Updated Model Number Description, Maintenance, 
Troubleshooting

ATTENTION:

 

Warnings, Cautions and Notices appear at 

appropriate sections throughout this literature. Read 
these carefully:

WARNING

Indicates a potentially hazardous 
situation which, if not avoided, could 
result in death or serious injury.

CAUTION

s

Indicates a potentially hazardous 
situation which, if not avoided, could 
result in minor or moderate injury. It 
could also be used to alert against 
unsafe practices.

NOTICE: 

Indicates a situation that could result in 
equipment or property-damage only 

WARNING

Proper Field Wiring and Grounding 
Required!

All field wiring MUST be performed by qualified 
personnel. Improperly installed and grounded field 
wiring poses FIRE and ELECTROCUTION hazards. To 
avoid these hazards, you MUST follow requirements for 
field wiring installation and grounding as described in 
NEC and your local/state electrical codes. Failure to 
follow code could result in death or serious injury. 

WARNING

Personal Protective Equipment (PPE) 
Required!

Installing/servicing this unit could result in exposure to 
electrical, mechanical and chemical hazards.

Before installing/servicing this unit, technicians 
MUST put on all Personal Protective Equipment (PPE) 
recommended for the work being undertaken. 
ALWAYS refer to appropriate MSDS sheets and OSHA 
guidelines for proper PPE. 

When working with or around hazardous chemicals, 
ALWAYS refer to the appropriate MSDS sheets and 
OSHA guidelines for information on allowable 
personal exposure levels, proper respiratory 
protection and handling recommendations. 

If there is a risk of arc or flash, technicians MUST put 
on all Personal Protective Equipment (PPE) in 
accordance with NFPA 70E or other country-specific 
requirements for arc flash protection, PRIOR to 
servicing the unit.

Failure to follow recommendations could result in death 
or serious injury.

Содержание Precedent WSC060ED


































Отзывы: