background image

Pre-Start

RT-SVX39B-EN

27 

Use the checklist provided below in conjunction with the 
“General Unit Requirements” checklist to ensure that the 
unit is properly installed and ready for operation.

Check all electrical connections for tightness and 
“point of termination” accuracy.

Verify that the condenser airflow will be unobstructed.

Verify that the condenser fan and indoor blower turn 
freely without rubbing and are properly tightened on 
the shafts.

Check the supply fan belts for proper tension and the 
fan bearings for sufficient lubrication. If the belts 
require adjustment, or if the bearings need lubricating, 

refer to the maintenance section of this manual for 
instructions.

Verify that a condensate trap is installed and the piping 
is properly sized and pitched.

Verify that the correct size and number of filters are in 
place. 

Inspect the interior of the unit for tools and debris and 
install all panels in preparation for starting the unit.

Voltage Imbalance

Three phase electrical power to the unit must meet 
stringent requirements for the unit to operate properly. 
Measure each leg (phase-to-phase) of the power supply. 
Each reading must fall within the utilization range stamped 
on the unit nameplate. If any of the readings do not fall 
within the proper tolerances, notify the power company to 
correct this situation before operating the unit.

Excessive three phase voltage imbalance between phases 
will cause motors to overheat and eventually fail. The 
maximum allowable voltage imbalance is 2%. Measure 
and record the voltage between phases 1, 2, and 3 and 
calculate the amount of imbalance as follows: 

V1, V2, V3 = Line Voltage Readings

VD = Line Voltage reading that deviates the farthest from 
the average voltage.

Example: If the voltage readings of the supply power 
measured 221, 230, and 227, the average volts would be:

VD (reading farthest from average) = 221

The percentage of Imbalance equals:

The 2.2% imbalance in this example exceeds the 
maximum allowable imbalance of 2.0%. This much 
imbalance between phases can equal as much as a 20% 
current imbalance with a resulting increase in motor 
winding temperatures that will decrease motor life. If the 
voltage imbalance is over 2%, notify the proper agencies 
to correct the voltage problem before operating this 
equipment.

Electrical Phasing (Three Phase Motors)

The compressor motor(s) and the supply fan motor are 
internally connected for the proper rotation when the 
incoming power supply is phased as A, B, C.

Table  5.

Temperature versus resistance (temperature vs. 
resistance is negative)

Temperature

Degrees F° Degrees C°

Nominal 

Resistance

-20°

-28.9°

170.1 K - Ohms

-15°

-26.1°

 143.5 K - Ohms

-10°

-23.3°

121.4 K - Ohms

-5°

 -20.6°

103.0 K - Ohms

 -17.8°

87.56 K - Ohms

 -15.0°

74.65 K - Ohms

10°

 -12.2°

63.80 K - Ohms

15°

-9.4°

54.66 K - Ohms

20°

-6.7°

46.94 K - Ohms

25°

-3.8°

40.40 K - Ohms

30°

-1.1°

34.85 K - Ohms

35°

1.7°

30.18 K - Ohms

40°

4.4°

26.22 K - Ohms

45°

7.2°

22.85 K - Ohms

50°

10.0°

19.96 K - Ohms

55°

12.8°

17.47 K - Ohms

60°

15.6°

15.33 K - Ohms

65°

18.3°

13.49 K - Ohms

70°

21.1°

11.89 K - Ohms

75°

23.9°

10.50 K - Ohms

80°

26.7°

9.297 K - Ohms

85°

29.4°

8.247 K - Ohms

90°

32.2°

7.330 K - Ohms

95°

35.0°

6.528 K - Ohms

100°

37.8°

5.824 K - Ohms

WARNING

Hazardous Voltage!

Disconnect all electric power, including remote 
disconnects before servicing. Follow proper lockout/
tagout procedures to ensure the power can not be 
inadvertently energized. Failure to disconnect power 
before servicing could result in death or serious injury.

% Voltage Imbalance = 

100 X AV - VD 

where;

AV

AV (Average Voltage) 

Volt 1 + Volt 2 + Volt 3 

3

221 + 230 + 227 

= 226 Avg.

3

100 X 226 - 221 

= 2.2%

226

Содержание Precedent WSC060ED


































Отзывы: