Trane IntelliPak Signature SCRF-020 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 108

background image

SCXF-SVX01B-EN

33

Pre-Startup
Requirements

Static Pressure Transducer
Installation (VAV units only)

Supply air static pressure controls the
inlet guide vane and inverter options. A
static pressure head assembly ships
separate in the control panel for field
installation in the supply air duct work.
The installer is responsible for providing
pneumatic tubing.

Transducer Location
Place the head assembly in an area of the
ductwork that will provide an average
and evenly distributed airflow pattern.
Use the following guidelines to determine
an appropriate installation location.

1. Locate the static head assembly about

two-thirds to three- fourths of the way
down the longest duct run, in an area
approximately 10 duct diameters
downstream and 2 duct diameters
upstream of any major interferences,
turns, or changes in duct diameter.

2. When installing pneumatic tubing

between the head assembly and
transducer in the control panel, do not
exceed 250 feet for

1

/

4

” OD tubing or

500 feet for

3

/

8

” OD tubing.

Installing the Transducer
Complete the following procedure to
properly install the inlet guide vane static
pressure transducer.
1. Mount the pressure sensing head

assembly in the duct so that the sensing
tip is in the middle of the duct, and
perpendicular to the airflow. This will
provide proper pressure measurement.
See Figure I-PR-6.

2. Connect the pneumatic tubing from the

sensing head to the push-on tubing
connection in the control panel. Use a
plastic static pickup tubing. Do not
exceed 250 feet for

1

/

4

“ OD tubing or

500 feet for

3

/

8

” OD tubing.

The transducer inside the control panel
picks up low side or reference pressure.

Note: If plastic tubing pulls away from a
connection, trim it back before replacing it
on the fitting. Stretched tubing may leak
and cause faulty control.

Figure I-PR-6. Static pressure sensor installation.

Installation

«
...
31
32
33
34
35
...
»

Содержание IntelliPak Signature SCRF-020













































































































Отзывы:

Нет отзывов

Похожие инструкции для IntelliPak Signature SCRF-020

Бренд: Magic-Pak Страницы: 5

Бренд: Daikin Страницы: 5

Бренд: inventum Страницы: 100

Бренд: Toyotomi Страницы: 38

Бренд: CLIVET Страницы: 40

Бренд: Sakura Страницы: 20

Бренд: JustFire Страницы: 14

OmniXAirFreshener

Бренд: Mini Gadgets Страницы: 20

22-11-2222N-003

Бренд: Maytag Страницы: 26

Бренд: MICAN Страницы: 292

GWH18RC-K3DNA1A

Бренд: Gree Страницы: 92

Бренд: REMKO Страницы: 28

Бренд: CAA Страницы: 42

Бренд: TECO Страницы: 21

Бренд: ELwell Страницы: 12

Бренд: Kaysun Страницы: 64

Бренд: Sonnenkonig Страницы: 36

AirHub Portable 113.0666.175

Бренд: FABER S.p.A. Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды