Trane IntelliPak Signature SCRF-020 Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 108

background image

SCXF-SVX01B-EN

81

Owner

Maintenance Procedures

Air Filters
Filter access doors are on the unit’s left
side. Filter access for the 2” or 4” filter
rack on optional steam and hot water
coils and airside economizers is also on

Figure O-M-1. Unit Filter Sizes and Placement for SXWF 20-42 Tons or SXRF 20-40 Tons.

Without Steam or Hot Water Coil

With Steam or Hot Water Coil

Note: Filters can be 2 or 4". These views are from the back of the unit (L-R).

Note: All filters are 2". These views are from the back of the unit (L-R).

18 x 20 18 x 20 18 x 20 18 x 20

20 x 20

20 x 20 20 x 20 20 x 20

18 x 20 18 x 20 18 x 20 18 x 20

16 x 20 16 x 20 16 x 20 16 x 20

20 x 20

20 x 20 20 x 20 20 x 20

20 x 20 20 x 20 20 x 20 20 x 20

Without Hot Water or Steam Coil

Note: Filters can be 2 or 4". These views are from the back of the unit (left to right).

With Hot Water or Steam Coil

Note: All filters are 2". These views are from the back of the unit (left to right).

25 x 20 25 x 16 25 x 16 25 x 16 25 x 16 25 x 20

20 x 20 16 x 20 16 x 20 16 x 20 16 x 20 20 x 20

25 x 20 25 x 16 25 x 16 25 x 16 25 x 16 25 x 20

20 x 25 16 x 25 16 x 25 16 x 25 16 x 25 20 x 25

20 x 20 16 x 20 16 x 20 16 x 20 16 x 20 20 x 20

20 x 25 16 x 25 16 x 25 16 x 25 16 x 25 20 x 25

the left side of the unit. To replace
throwaway filters, remove the dirty
elements and install new filters with the
filter’s directional arrows pointing toward
the fan. Verify that no air bypasses the
filters. See Figures O-M-1 and O-M-2 for
proper filter placement.

Maintenance

Figure O-M-2. Unit Filter Sizes and Placement for SXWF 42-80 Tons or SXRF 40-60 Tons.

«
...
79
80
81
82
83
...
»

Содержание IntelliPak Signature SCRF-020













































































































Отзывы:

Нет отзывов

Похожие инструкции для IntelliPak Signature SCRF-020

Бренд: Magnavox Страницы: 19

Бренд: EdgeStar Страницы: 23

Бренд: Trane Страницы: 32

Бренд: York Страницы: 30

Бренд: York Страницы: 30

Бренд: ARCTIC WIND Страницы: 20

Бренд: Trane Страницы: 34

Бренд: IQAir Страницы: 28

Бренд: MAXA Страницы: 44

Бренд: nedis Страницы: 16

50PG08 14 Series

Бренд: Carrier Страницы: 20

Бренд: Toyotomi Страницы: 48

Бренд: EUROM Страницы: 52

Бренд: Daikin Страницы: 23

Air Purifier 60

Бренд: Airfree Страницы: 24

Бренд: Orava Страницы: 115

Бренд: Indel B Страницы: 100

Precedent YSC060-120

Бренд: Trane Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды