Trane IntelliPak Signature SCRF-020 Скачать руководство пользователя страница 48

Страница: 48 / 108

SCXF-SVX01B-EN

Programming

Installation

Figure I-P-2. BAYSENS020 Keypad and display configuration.

BAYSENS020

BAYSENS020 Keypad and Display
Explanation

1. Up and Down Buttons
• Increases or decreased programmed

temperature settings in program menu.

• Shifts to temporary manual override in

normal run mode.

•Increases or decreases temperature

while in temporary override menu.

• Pressed together, toggles between

unoccupied/occupied setting.

2. Time Adjust Button
Used to set the correct time of day. Used
to set programmed time for temperature
variations.

3. Program Button
Toggles between the display control
screen and the display program screen.

4. Erase Button
• Erases time and temperature settings

throughout each of the programmed
periods.

• Exits temporary manual override.

5. Day Button
Toggles through the seven days of the
week.

6. Hold Temp Button
Shifts controller to temporary manual
override, and begins temperature
override.

7. Mode Button
• Toggles the controller between the two

modes, off and auto.

• Advances to next setpoint in program

menu.

8. During Programming Indicates:
• Heat supply air
• Cool supply air
• Warmup temperature

Содержание IntelliPak Signature SCRF-020













































































































Результаты поиска

Содержание IntelliPak Signature SCRF-020

Отзывы:

Похожие инструкции для IntelliPak Signature SCRF-020

Бренды по названию

Популярные бренды

Trane IntelliPak Signature SCRF-020, Инструкция по установке, эксплуатации и диагностике

Результаты поиска

Содержание IntelliPak Signature SCRF-020

Отзывы:

Похожие инструкции для IntelliPak Signature SCRF-020

Бренды по названию

Популярные бренды