background image

59

Service & Maintenance

Annual Maintenance

[ ] Perform all weekly and monthly maintenance proce-

dures.

[ ] Have a qualified service technician check the setting and

function of each control and inspect the condition of and
replace compressor and control contactors if needed.

[ ] If chiller is not piped to drain facilities, make sure drain is

clear to carry away system water.

[ ] Drain water from evaporator and associated piping sys-

tems. Inspect all piping components for leakage, dam-
age, etc. Clean out any in-line water strainers.

[ ] Clean and repaint any corroded surface.

[ ] Check low ambient dampers for proper operation.

[ ] Clean condenser coils. Refer to "Coil Cleaning".

WARNING

Hazardous Voltage!

Disconnect all electric power, including remote discon-
nects before servicing. Follow proper lockout/tagout
procedures to ensure the power can not be inadvert-
ently energized. Failure to disconnect power before ser-
vicing could result in death or serious injury.

[ ] Inspect the expansion valve sensing bulbs for cleanli-

ness. Clean if required. Sensing bulbs must make good
contact with suction lines and be properly insulated.

[ ] Clean condenser fans. Check fan assemblies for proper

orifice clearance and for motor shaft mis-alignment, ab-
normal end-play or vibration and noise.

WARNING

Rotating Components!

During installation, testing, servicing and troubleshoot-
ing of this product it may be necessary to measure the
speed of rotating components. Have a qualified or li-
censed service individual who has been properly
trained in handling exposed rotating components, per-
form these tasks. Failure to follow all safety precau-
tions when exposed to rotating components could re-
sult in death or serious injury.

Final Process

For future reference, you may find it helpful to record the
unit data requested below in the blanks provided.

(1) Complete Unit Model Number:

______________________________________
______________________________________

(2) Unit Serial Number:

______________________________________
______________________________________

(3) Unit "DL" Number ("design special" units only):

______________________________________
______________________________________

(4) Wiring Diagram Numbers (from unit control panel):

— schematic(s)

______________________________________
______________________________________
______________________________________
______________________________________

— connection(s)

______________________________________
______________________________________
______________________________________
______________________________________

Unit Address (TCI)

______________________________________

Network ID (LCI)

______________________________________

Содержание IntelliPak CG-SVX02B-EN

































































Отзывы: