Trafox SUPERINTEND IM-01.IND Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 50

Trafox SUPERINTEND IM-01.IND Скачать руководство пользователя страница 16

16

© Copyright Muuntosähkö Oy

–

Trafox

Superintend IMD

http://www.trafox.fi

•

The Monitor menu mainly has one level. Nearly all information to be displayed can
be viewed by browsing the menu with the and buttons.

•

The Alarm menu has two levels. The first level displays the reason for the alarm
and the second level shows the alarm start time, the measured parameters, and
alarm limits.

•

The Setup menu mainly has two levels. The first level displays the valid
parameter, which can be changed on the second level.

Hereafter, the screen modes are called as follows:

•

The

main level

of the menu is the topmost menu level (MONITOR, SETUP and

ALARM)

•

The

menu level

is the sub-level of the aforementioned, and it is browsed using

the and buttons

•

The

screen mode

is the mode following the menu level, and it displays the value

of the parameter/time; also displays a stopped AutoScroll mode. The screen
mode can be accessed from the menu level by pressing the T button.

•

The

AutoScroll

mode is in use in the Setup menu items where there are several

parameters to display. In that case, the displayed parameters change every few
seconds. You can stop the display with the and buttons and return from the
screen mode to the AutoScroll mode with the B button. Use the T button to go to
the edit mode or screen mode.

•

The

Edit mode

is a Setup menu mode where the parameters to be displayed can

be changed. In the Edit mode, the parameter to be changed flashes and it can be
changed with the   and   buttons. If there are several parameters to be
changed in the same screen, you can move to the next one by pressing the
button.  After the editing is completed, press the T  button, after which the values

given must be approved by selecting “Yes” in the Confirm menu and pressing T.
By selecting “No” or pressing the B button in the conformation stage you return

to the previous mode without saving the changes.

As a rule, the buttons function as follows:

«
...
14
15
16
17
18
...
»

Содержание SUPERINTEND IM-01.IND



















































Отзывы:

Нет отзывов