Toyota ESP9000 Скачать руководство пользователя страница 89

Страница: 89 / 111

3.ADJUSTMENT

3-10. Limit sensor

[Inspection]

(1)

Loosen two setting screws (a) remove

the table set. (Fig.1)

(2)

Remove four set screws (e) and then

base cover rear L. (Fig 1)

(3) Remove two setting screws (c) and

the then base cover rearL. (Fig.1)

(4) Remove three set screws (b) and then

base cover front L. (Fig.1)

(5) Remover four set screws (d) and then

X cover. (Fig.1)

(6) Turn power on and carry out home

position return.

Note: Press the［SET］key.

(7) Check the distance X from the right

most surface of the detecting plate to

the center of left side X limit sensor

shown in Fig.2.

(8) Move the X-axis drive system to its

forefront position and check the

distance Y from the back most

surface of the detecting plate to the

center of middle side Y limit sensor.

(Fig.2)

Reference: X=65.7±1mm

Y =213.5 ± 1mm (Flat

frame)

’

=133.5 ± 1mm (Cap

frame)

X cover

Motor
cover

(c)

Base c
front L

over

(e)

(b)

FIG.1

X-axis
drive

Limit
sensor

Detecting plate (slit)

Slit

Table set

(a)

(d)

Base cover
rear L

-34-

Содержание ESP9000
















































































































Результаты поиска

Содержание ESP9000

Отзывы:

Похожие инструкции для ESP9000

Бренды по названию

Популярные бренды

Toyota ESP9000, Руководство по обслуживанию

Результаты поиска

Содержание ESP9000

Отзывы:

Похожие инструкции для ESP9000

Бренды по названию

Популярные бренды