Toyota ESP9000 Скачать руководство пользователя страница 17

Страница: 17 / 111

FIG.2

FIG.3

FIG.4

4-14. X motor

［Removal］

(1) Remove two setting screws (a) and

motor cover. (Fig.1).

(2) Loosen the nut and remove the

setting screw (b). (Fig.2)

(3) Disconnect the connectors. Remove

two setting screws (c) and the X

motor. (Fig.2)

(4) Remove four setting screws (d) and X

motor from the bracket. (Fig.2)

［Installation］

Power circuit board

Lower shat joint

(1) Mount the X motor to the motor base

with four setting screws (d) (Fig.2).

Sewing machine
motor

(c)

(2) Set the X motor gear to the belt and

temporarily secure the motor base to

the X base B with two setting screws

Arm bed

(3) Adjust the belt tension by setting

screw (b) and firmly tighten two

setting screws (c), then tighten the

nut. (Figs.2, 3)

Power circuit board

Note: Check the tension, after tighting

screws (c).

(4) Insert the connector.

(d)

Sewing machine
motor

4.REPLACEMENT OF MAIN COMPONENTS

(a)

Motor cover

-52-

Содержание ESP9000
















































































































Результаты поиска

Содержание ESP9000

Отзывы:

Toyota ESP9000, Руководство по обслуживанию, Страница: 17 / 111

Результаты поиска

Содержание ESP9000

Отзывы: