Toyota 2003 MR2 Spyder Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 318

background image

46

2003 MR2 from Aug. ’03 Prod. (OM17511U)

The indicator comes on when the passen-
ger airbag system is off.

To check the airbag cut–off system status,
turn the ignition switch to the “ON” posi-
tion. The “AIRBAG” warning light and the
“OFF” indicator light should go on for
approximately 4 seconds. If the airbag
switch is turned off, the “OFF” indicator
will continue to illuminate, and if the air-
bag switch is turned on, the “OFF” indica-
tor will not illuminate.

CAUTION

Make sure that the indicator light is
off.

Do not turn off the passenger air-
bag manual on–off switch except
when a member of a passenger risk
group identified in TABLE 1 (on
page 40) is occupying the passen-
ger seating position.

When the passenger airbag manual
on–off switch is turned off, the pas-
senger airbag will not inflate in a
collision and turning off the pas-
senger airbag can reduce the occu-
pant protection which your vehicle
safety systems can provide to you
in certain accidents and increase
the likelihood of serious personal
injuries.

For details, see “SRS driver airbag
and passenger airbag” on page 37 in
this Section.

Toyota strongly urges the use of ap-
propriate child restraint systems for
children.

The laws of all 50 states in the U.S.A.
now require the use of a child restraint
system.

Your vehicle conforms to SAEJ1819.

CAUTION

For effective protection in automo-
bile accidents and sudden stops, a
child must be properly restrained,
using a seat belt or child restraint
system depending on the age and
size of the child. Holding a child in
your arms is not a substitute for a
child restraint system. In an acci-
dent, the child can be crushed
against the windshield, or between
you and the vehicle’s interior.

Toyota strongly urges use of a
proper child restraint system that
conforms to the size of the child.

03 07.07

Child restraint—
—Child restraint precautions

«
...
60
61
62
63
64
...
»

Содержание 2003 MR2 Spyder































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2003 MR2 Spyder

Electronic Parking Disc II

Бренд: Jacob Jensen Страницы: 28

V2 SUPERCHARGER

Бренд: Tesla Страницы: 9

Бренд: Chevrolet Страницы: 356

Бренд: Ford Страницы: 272

Бренд: Pontiac Страницы: 376

Бренд: Jeep Страницы: 712

Бренд: Lexus Страницы: 369

Бренд: Mountain Top Страницы: 12

Бренд: Nav TV Страницы: 3

Бренд: iArmor Страницы: 4

Бренд: Motoalliance Страницы: 8

Бренд: Thule Страницы: 8

Бренд: Billien Страницы: 2

Бренд: Lexus Страницы: 28

Бренд: Axxess Страницы: 16

Бренд: Saab Страницы: 288

Бренд: Kargo Master Страницы: 18

Бренд: Skoda Страницы: 276

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды