manualshive.com logo in svg

Toyota 2003 MR2 Spyder, Руководство пользователя


Поделиться
Скачать
background image

214

2003 MR2 from Aug. ’03 Prod. (OM17511U)

The tires on your Toyota have built–in
tread wear indicators to help you
know when the tires need replace-
ment. When the tread depth wears to
1.6 mm (0.06 in.) or less,  the indica-
tors will appear. If you can see the
indicators in two or more adjacent
grooves, the tire should be replaced.
The lower the tread, the higher the
risk of skidding.

Vehicles equipped with 185/55R15
or 215/45R16 tires: Your Toyota has
been fitted with specially developed
tires which provide exceptional dy-
namic performance under general
road conditions. However your riding
comfort may worsen a little and road
noise may increase during driving.
You may also notice that your tires
will wear more rapidly and tire grip
performance will be reduced on the
snowy and/or icy roads when
compared to standard tires. Be sure
to have snow tires or tire chains on
the snowy and/or icy roads and drive
carefully with the speed appropriate
for road conditions.

NOTICE

Low profile tire like 185/55R15
or 215/45R16 may have greater
damage than usual tires to its
tire wheel when receiving im-
pact from the road surface.
Therefore, pay attention to the
followings.

Be sure to use with proper
tire pressure. If the tire pres-
sure is low, the tire may
have a greater damage. For
detailed information about
tire pressure, see page 242 in
Section 8.

Avoid driving onto high,
sharp–edged objects and oth-
er road hazards. Failure to
do so can lead to severe tire
damage.

The effectiveness of snow tires is
lost if the tread wears down below
4 mm (0.16 in.).

If you have tire damage such as
cuts, splits, cracks deep enough to
expose the fabric, or bulges indi-
cating internal damage, the tire
should be replaced.

If a tire often goes flat or cannot be
properly repaired due to the size or
location of a cut or other damage, it
should be replaced. If you are not
sure, consult with your Toyota dealer.

If an air loss occurs while driving, do
not continue driving with a deflated
tire. Driving even a short distance can
damage a tire beyond repair.

Any tires which are over 6 years
old must be checked by a qualified
technician even  if damage is not
obvious.

Tires deteriorate with age even if they
have never or seldom been used.

03 07.07

Содержание 2003 MR2 Spyder































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2003 MR2 Spyder

Harbor Freight Tools 92043 Assembly And Operating Instructions preview
92043
Бренд: Harbor Freight Tools Страницы: 4
Havis-Shields 1997-2007 Dodge Dakota Telescoping Computer Base C-TCB-28 Install Instructions preview
1997-2007 Dodge Dakota Telescoping Computer Base C-TCB-28
Бренд: Havis-Shields Страницы: 3
Saab 92X Owner'S Manual preview
92X
Бренд: Saab Страницы: 445
Raytel LLC TellPhone 4200 Installation Instructions & Operating Manual preview
TellPhone 4200
Бренд: Raytel LLC Страницы: 40
RBO RBO4038 Product Manual preview
RBO4038
Бренд: RBO Страницы: 15
Caltrend LY115 Installation Instructions preview
LY115
Бренд: Caltrend Страницы: 3
Kia Picanto Manual preview
Picanto
Бренд: Kia Страницы: 680
Cadillac 2011 SRX CROSSOVER Owner'S Manual preview
2011 SRX CROSSOVER
Бренд: Cadillac Страницы: 416
TIE DOWN LONGRUN 86103 Assembly/Installation Instructions preview
LONGRUN 86103
Бренд: TIE DOWN Страницы: 2
Saab 2000 9-5 2.3 Turbo Ecopower Owner'S Manual preview
2000 9-5 2.3 Turbo Ecopower
Бренд: Saab Страницы: 256
Griffin Technology iTrip Bluetooth User Manual preview
iTrip Bluetooth
Бренд: Griffin Technology Страницы: 6
Mitsubishi Pajero Pinin 1999 Workshop Manual preview
Pajero Pinin 1999
Бренд: Mitsubishi Страницы: 919
CARFACE CF145962E Instruction Manual preview
CF145962E
Бренд: CARFACE Страницы: 16
Vmac A700308 Installation Manual preview
A700308
Бренд: Vmac Страницы: 16
Volvo 2009 S40 Owner'S Manual preview
2009 S40
Бренд: Volvo Страницы: 286
JBA 1674S Installation Instructions preview
1674S
Бренд: JBA Страницы: 5
Waeco MagicWatch MWE150 Installation And Operating Manual preview
MagicWatch MWE150
Бренд: Waeco Страницы: 176
Directed Directechs FORD11 Installation Manual preview
Directechs FORD11
Бренд: Directed Страницы: 23

Бренды по названию

Популярные бренды

Загрузить еще бренды