Toyota 2003 MR2 Spyder Скачать руководство пользователя страница 263 | Manualshive

Страница: 263 / 318

background image

193

2003 MR2 from Aug. ’03 Prod. (OM17511U)

If you are a skilled do–it–yourself
mechanic, the Toyota service manuals are
recommended. Please be aware that
do–it–yourself maintenance can affect your
warranty coverage. See “Owner’s Warranty
Information Booklet” or “Owner’s Manual
Supplement” for the details.

General maintenance

Listed below are the general maintenance
items that should be performed as fre-
quently as specified. In addition to check-
ing the items listed, if you notice any
unusual noise, smell or vibration, you
should investigate the cause or take your
vehicle to your Toyota dealer or a quali-
fied service shop immediately. It is recom-
mended that any problem you notice be
brought to the attention of your dealer or
the qualified service shop for their advice.

CAUTION

Make these checks only with ade-
quate ventilation if you run the en-
gine.

IN THE ENGINE COMPARTMENT

Items listed below should be checked
from time to time, e.g. each time when
refueling.

Washer fluid
Make sure there is sufficient fluid in the
tank. See page 225 in Section 7–3 for
additional information.

Engine coolant level
Make sure the coolant level is between
the “FULL” and “LOW” lines on the see–
through reservoir when the engine is cold.
See page 208 in Section 7–2 for addition-
al information.

Radiator, condenser and hoses
Check that the front of the radiator and
condenser are clean and not blocked with
leaves, dirt, or insects. See page 209 in
Section 7–2 for additional information.

Battery electrolyte level
Make sure the electrolyte level of all bat-
tery cells is between upper and lower lev-
el lines on the case. Add only distilled
water when replenishing. See page 222 in
Section 7–3 for additional information.

Brake fluid level
Make sure the brake fluid level is correct.
See page 209 in Section 7–2 for addition-
al information.

Engine oil level
Check the level by the dipstick with the
engine turned off and the vehicle parked
on a level spot. See page 206 in Section
7–2 for additional information.

03 07.07

«
...
261
262
263
264
265
...
»

Содержание 2003 MR2 Spyder































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2003 MR2 Spyder

Бренд: Yakima Страницы: 11

Бренд: Ford Страницы: 22

Бренд: FORM FIT Страницы: 2

Бренд: Edelbrock Страницы: 1

Бренд: FORM FIT Страницы: 2

Autostacker PL-6SR

Бренд: BendPak Страницы: 104

Бренд: Rati Страницы: 2

Бренд: Honda Страницы: 4

SAFESTOP SS0005

Бренд: Pro-gard Страницы: 4

Бренд: Veigel Страницы: 24

Бренд: Cellular Line Страницы: 25

Truck Training Model

Бренд: WABCO Страницы: 56

Бренд: Skoda Страницы: 281

Бренд: Bestop Страницы: 5

Бренд: PowerMadd Страницы: 3

Бренд: Yakima Страницы: 15

Бренд: Paccar Страницы: 63

Бренд: ECS Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды