Toyota 2003 MR2 Spyder Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 318

background image

90

2003 MR2 from Aug. ’03 Prod. (OM17511U)

3. Release the parking brake and brake

pedal. Depress the accelerator pedal
slowly for smooth starting.

CAUTION

Unlike automatic transmission mod-
els, the sequential manual transmis-
sion models do not creep.

NOTICE

On a slippery surface, it is possible
to start off with the gear in 2nd,
but to protect the clutch, try to
start using the 1st gear whenever
possible.

If the gear cannot be engaged to
1st when the selector lever is
shifted from the “N” to “S” posi-
tion, try to shift the selector lever
to the “N” position once, then shift
it to “S” position a few seconds
later.

(f) Starting off on an uphill/downhill

—Uphill

1. Apply the parking brake firmly so that

the vehicle does not roll backwards.

2. Shift the selector lever to the “S” posi-

tion while holding down the brake pe-
dal. Make sure that the gear position
indicator in the instrumental cluster dis-
plays 1st gear.

3. Release the brake pedal and depress

the accelerator pedal gradually, and
when the vehicle starts to move, re-
lease the parking brake and depress
the accelerator pedal to start off.

—Downhill

1. Hold down the brake pedal and shift

the selector lever to the “S” position.
Make sure by using the gear position
indicator that the gear is in 1st.

2. Release the brake pedal, and depress

the accelerator pedal slowly. Even
though the accelerator pedal is not de-
pressed, when the vehicle speed in-
creases, the clutch will be engaged
and the engine brake will be applied.

CAUTION

Unlike automatic transmission mod-
els, the sequential manual transmis-
sion models will not creep.

NOTICE

Do not hold the vehicle on an uphill
with the accelerator pedal applied.
Doing so may damage the clutch. Al-
ways use the brake pedal or parking
brake.

03 07.07

«
...
108
109
110
111
112
...
»

Содержание 2003 MR2 Spyder































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2003 MR2 Spyder

Бренд: Jeep Страницы: 42

Бренд: Jeep Страницы: 44

Бренд: Cadillac Страницы: 20

Бренд: Jeep Страницы: 7

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 354

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 10

2013 Escalade ESV

Бренд: Cadillac Страницы: 524

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 438

Бренд: Cadillac Страницы: 450

2011 Escalade Hybrid

Бренд: Cadillac Страницы: 94

2011 Escalade Hybrid

Бренд: Cadillac Страницы: 94

Бренд: Cadillac Страницы: 78

Бренд: Cadillac Страницы: 8

Бренд: Cadillac Страницы: 113

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды