Toyota 2003 MR2 Spyder Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 318

background image

91

2003 MR2 from Aug. ’03 Prod. (OM17511U)

SD16019

(g) Backing up

While holding down the brake pedal, shift
the selector lever to the “R” position. The
reverse warning buzzer will sound at this
time. Depress the accelerator pedal slow-
ly, as when starting off. Before driving off,
make sure by using the gear position indi-
cator that the gear is in reverse.

When the gear will not engage even
though the selector lever is shifted to the
“R” from “N” position, the “N” indicator will
flash and a warning buzzer (long pulse
sound) will sound. In this case, the sys-
tem will re–try shifting, or the driver can
operate the selector lever to shift, as fol-
lows.

The system will re–try shifting automat-
ically. This will take some time, noise
may be heard from the gears, and shift
shock may occur. However, they do not
indicate malfunction.

The driver can shift the selector lever
to the “N” position once, then shift to
the “R” position.

NOTICE

The system will not allow shifting
to the “R” position if the vehicle
speed is over 3 km/h (2 mph). In
case the selector lever is operated
under this condition, the “N” indica-
tor in the instrument cluster will
flash. However, when the vehicle
speed drops below 3 km/h (2 mph),
the gear is shifted to reverse. Make
sure that the vehicle has stopped
completely before shifting to the
“R” position.

Do not hold the vehicle on an uphill
with the accelerator pedal applied.
Doing so may damage the clutch.
Always use the brake pedal or park-
ing brake.

If the gear cannot be engaged to
reverse when the selector lever is
shifted from the “N” to “R” posi-
tion, try to shift the selector lever
to the “N” position once, then shift
it to “R” position a few seconds
later.

(h) Stopping

The vehicle can be stopped by depressing
the brake pedal regardless of the gear
position. This is because the clutch is
automatically disengaged to prevent the
engine from stopping. If the selector lever
is in the “S” position, the gear will be
downshifted to 1st when the vehicle stops.
However, if you do not drive the vehicle
over 40 km/h (24 mph) or convert the
drive position after starting with the gear
in 2nd, the gear will not be downshifted
to 1st when the vehicle stops the next
time and the gear is left in 2nd.

When stopping, for example, at a traffic
light, be sure to shift the selector lever to
the “N” position, and depress the brake
pedal firmly. For your safety, apply parking
brake, too, when stopping on a hill.

03 07.07

«
...
109
110
111
112
113
...
»

Содержание 2003 MR2 Spyder































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2003 MR2 Spyder

Бренд: Panasonic Страницы: 2

CYRC50U - UNIVERSAL REAR-VIEW CAMERA

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 12

Бренд: Edelbrock Страницы: 2

Бренд: iOttie Страницы: 58

Бренд: TrailFX Страницы: 2

Бренд: KLAUS Multiparking Страницы: 72

Бренд: BMW Страницы: 40

XC70 - ANNEXE 808

Бренд: Volvo Страницы: 8

Electronic Parking Disc 3

Бренд: Jacob Jensen Страницы: 17

C-5 CUT OUT COCK

Бренд: BENDIX Страницы: 2

20111 Highlander

Бренд: Toyota Страницы: 9

Бренд: HawksHead Страницы: 10

Бренд: Buick Страницы: 20

Бренд: Westin Страницы: 3

Бренд: Van Guard Страницы: 12

Бренд: MSD Страницы: 16

FARP WORKS CRUSHED CAR

Бренд: Cramaro Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды