Toyota 2003 MR2 Spyder Скачать руководство пользователя страница 288 | Manualshive

Страница: 288 / 318

background image

218

2003 MR2 from Aug. ’03 Prod. (OM17511U)

CHAIN INSTALLATION

Install the chains on the rear tires as
tightly as possible. Do not use tire
chains on the front tires. Retighten
chains after driving 0.5—1.0 km
(1/4—1/2 mile).

When installing chains on your tires, care-
fully follow the instructions of the chain
manufacturer.

CAUTION

Do not exceed 50 km/h (30 mph) or
the chain manufacturer’s recom-
mended speed limit, whichever is
lower.

Drive carefully avoiding bumps,
holes, and sharp turns, which may
cause the vehicle to bounce.

Avoid sharp turns or locked–wheel
braking, as use of chains may ad-
versely affect vehicle handling.

When driving with chains installed,
be sure to drive carefully. Slow
down before entering curves to
avoid losing control of the vehicle.
Otherwise an accident may occur.

NOTICE

Do not attempt to use a tire chain on
the compact spare tire, as it may re-
sult in damage to the vehicle as well
as the tire.

Replacing wheels

WHEN TO REPLACE YOUR WHEELS

If you have wheel damage such as
bending, cracks or heavy corrosion, the
wheel should be replaced.

If you fail to replace a damaged wheel,
the tire may slip off the wheel or cause
loss of handling control.

WHEEL SELECTION

When replacing wheels, care should be
taken to ensure that the wheels are re-
placed by ones with the same load ca-
pacity, diameter, rim width, and offset.

Correct replacement wheels are available
at your Toyota dealer.

A wheel of a different size or type may
adversely affect handling, wheel and bear-
ing life, brake cooling, speedometer/odom-
eter calibration, stopping ability, headlight
aim, bumper height, vehicle ground clear-
ance, and tire or snow chain clearance to
the body and chassis.

Replacement with used wheels is not rec-
ommended as they may have been sub-
jected to rough treatment or high mileage
and could fail without warning. Also, bent
wheels which have been straightened may
have structural damage and therefore
should not be used. Never use an inner
tube in a leaking wheel which is designed
for a tubeless tire.

03 07.07

«
...
286
287
288
289
290
...
»

Содержание 2003 MR2 Spyder































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2003 MR2 Spyder

Бренд: Lancia Страницы: 276

Бренд: T-Tech Страницы: 38

Бренд: Mitsubishi Страницы: 160

Бренд: Cadillac Страницы: 442

Бренд: Yakima Страницы: 13

Бренд: Menabo Страницы: 11

Бренд: Simplicity Страницы: 10

1506-PHX Cargo Plus

Бренд: Ranger design Страницы: 8

Бренд: AUTOTECH Страницы: 1

2013 GMC Savana

Бренд: GMC Страницы: 398

Бренд: Westin Страницы: 2

Бренд: THIEYE Страницы: 88

Бренд: Mobridge Страницы: 20

Бренд: GROM Audio Страницы: 20

Бренд: Aston Martin Страницы: 415

Бренд: Buick Страницы: 112

Бренд: Erich Jaeger Страницы: 16

Бренд: Camcar Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды