manualshive.com logo in svg

Town & Country Fireplaces D Series, Руководство по установке

Поделиться
Скачать
Town & Country Fireplaces D Series Скачать руководство пользователя страница 39

100001140

39

TCWS54STOK_270619-56

 Finishing Touch Trim Kit Installation 

Figure 79:  Installing the side trim.

Figure 80:  Side trim in place.

Figure 81:  Installing top trim.

Figure 82:  Top trim in place.

The trim kit includes two side pieces, a top piece, and a bottom meshed piece which will be placed 
onto the fireplace floor and in front of the glass once the fireplace door is installed.

Installation (Indoor side only)

1.  With the door in place, begin by setting out the two side trim pieces and the top piece. Each of 

these three trim pieces require 2 small button magnets which are included with the trim pieces.  

2.  Install the two side trim pieces first using two smaller magnets on each piece as shown in Figure 

79 and Figure 80.

3.  Install the top trim piece over top of the two side trim pieces using two larger magnets (Figure 81 

and Figure 82). 

Содержание D Series

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды