manualshive.com logo in svg

Town & Country Fireplaces D Series, Руководство по установке

Поделиться
Скачать
Town & Country Fireplaces D Series Скачать руководство пользователя страница 3

100001140

FOR YOUR SAFETY 

- Do not install or operate your Town & Country fireplace without first reading and understanding 

this manual.  Any installation or operational deviation from the following instructions voids the Town & Country Fireplaces 
Warranty and may prove hazardous.

This appliance and its individual shut off valve must be disconnected from gas supply piping system during any pressure 
testing of that system at test pressures in excess of 1/2 psig (3.5 kPa).

This appliance must be isolated from the gas supply piping system by closing its individual manual shut off valve during 
any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.5 kPa).

Note: When lit for the first time, the appliance will emit a slight odour for a couple of hours. This is due to the curing of 
paints, sealants and lubricants used in the manufacturing process. This condition is temporary. Open doors and windows 
to ventilate area. Smoke and fumes caused by the curing process may cause discomfort to some individuals.

Do not use the fireplace if any part has been under water. Immediately call a qualified service technician to inspect the 
fireplace and to replace any part of the control system and any gas control which has been under water.

Due to high temperatures, this gas appliance should be located out of traffic and away from furniture and draperies.

Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns 
or clothing ignition.

Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young 
children, and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are 
at-risk individuals in the house. To restrict access to a fireplace or stove, install an adjustable safety gate to keep 
toddlers, young children, and other at-risk individuals out of the room and away from hot surfaces. 

Clothing or other flammable material should not be placed on or near the appliance.

Any grill, panel or door removed for servicing the unit must be replaced prior to operating. Failure to do so may create a 
hazardous condition.

Installation and repair should be done by a qualified service person. The appliance should be inspected before use and 
at least annually by a professional service person. More frequent cleaning may be required due to excessive lint from 
carpeting, bedding material, etc. It is imperative that control compartments, burners and circulating air passageways of 
the appliance be kept clean.

It is our policy that no responsibility is assumed by the Company or by any of its employees or representatives for any 
damages caused by an inoperable, inadequate, or unsafe condition which is the result, either directly or indirectly, of any 
improper operation or installation procedures.

This appliance must not be connected to a chimney flue serving a separate solid fuel burning appliance.

It has been determined that the Town and Country model TCWS.54STOK indoor/outdoor Fireplace has an R value of 5.8.

This determination has been arrived at by the calculation of the typical R value of two layers of 5mm Ceramic glass, 
combined with 17 inches of ventilated air gap. The one layer of 5mm tempered glass has been ignored in the calculation 
due to it being open to the exterior air environment on both sides. Real world results may vary due to environmental 
factors.

3

TCWS54STOK_270619-56

 Caution 

 Safety 

 R - Value Statement 

Содержание D Series

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды