manualshive.com logo in svg

Town & Country Fireplaces D Series, Руководство по установке

Поделиться
Скачать
Town & Country Fireplaces D Series Скачать руководство пользователя страница 14

Figure 15:  Non combustible board within frame.

 54 1/16" 

 74 3/4" 

 20 5/16" 

 20 13/16"  - 23 13/16" 

Figure 18:  Frame kit dimensions.

100001140

Non-combustible board detail

Calcium silicate board

NON-COMBUSTIBLE
BOARD

If finishing the wall above the unit with 
paint, the framing kit shipped with 
the unit should be discarded. Use full 
sheets of calcium silicate board or 
equivalent and full length metal studs to 
finish and frame around the unit. 

Calcium silicate board is a high grade 
material with cement, quartz and natural 
minerals as the main raw materials. 
(Note: Calcium Silicate is 1/2” thick)

CAUTION: Calcium Silicate board 
can be damaged if dropped or struck. 
Handle with care. Inspect board prior to 
installation and do not use if cracked.

NOTE: It is recommended to pre-drill 
mounting holes in the board prior 
to securing to the framing. This will 
prevent the board from cracking.

Figure 17:  Non-combustible board  
 

 location.

NON-COMBUSTIBLE 
MATERIAL MUST EXTEND 
TO THE TOP EDGE AND TO 
THE SIDE EDGE OF THE 
FRAMING KIT.

NON-COMBUSTIBLE 
BOARD ONLY IN 
THESE AREAS

NOTE:  FIREPLACE SHOULD BE IN ITS FINAL LOCATION BEFORE FRAMING.

This fireplace may be recessed 
up to a maximum depth of 4 
1/2”. This  recess must be con-
structed from non- combustible 
material. 

It is important to note that any 
finishing material used must 
not interfere with the glass 
door being able to open in the 
event of ignition of excess gas 
buildup.

Figure 16:  TCWS54STOK Recessed installation details.

Non-combustible recessed 

installation detail

14

TCWS54STOK_270619-56

Содержание D Series

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды