manualshive.com logo in svg

Town & Country Fireplaces D Series, Руководство по установке

Поделиться
Скачать
Town & Country Fireplaces D Series Скачать руководство пользователя страница 19

Note:  Installation must be performed by a qualified installer, service agency or gas supplier.

Figure 31:  Wall switch - interface side.

The TCWS54STOK_D must be pre-set  

to the “PV” setting.

TO FIREPLACE

 Wall Switch and Remote Control 

 Selecting Natural Vent and Power Vent Modes 

Note: The wall switch for the TCWS54STOK must not have batteries installed in it. The batteries are for   
 

back up in case of a power outage. This fireplace must not operate with a battery back up.

Figure 30:  Town and Country  
 

wall switch.

Linking the remote control 

unit to the wall switch. 

1.  Begin by moving the selector 

toggle on the wall switch to the 
“REMOTE” position. 

2.   Insert a straightened paper clip 

into the “PROGRAM” slot on the 
wall switch. 

3.  Press the internal “PROGRAM” 

button once and wait until you 
hear 3 beeps from the wall switch. 

 

4.  Press the ON/OFF button of the  

remote unit.  Once the wall unit 
beeps 3 times, the remote is 
programmed.  

5.  The toggle on the wall switch 

must be kept in the “REMOTE” 
position in order to use the remote 
control unit. 

The NV/PV (Natural Vent / Power Vent) switch (Figure 33) 
on the interface board (Figure 29) is set according to which 
type of evacuating vent system is present. In all cases with 
the TCWS54STOK fireplace, the NV/PV switch MUST be 
set to PV. 

Figure 32:  Wall switch no batteries.

Figure 33:  Vent mode selection switch.

DO NOT install batteries in 

the wall switch

100001140

19

TCWS54STOK_270619-56

Содержание D Series

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды