manualshive.com logo in svg

Town & Country Fireplaces D Series, Руководство по установке

Поделиться
Скачать
Town & Country Fireplaces D Series Скачать руководство пользователя страница 36

Figure 73:  Installing first of two burners.

Installation:

SCREW

PILOT HOLE

GROMMETS

CAUTION: The burners should be tightly 

butted up against each other 
at the center to ensure correct 
operation.

NOTE: Check air shutter for correct fuel   

setting before proceeding further. 
Both burner shutters are to be set 
the same, fully closed for natural 
gas. 13/64 (0.2)” open for LP.

If converting to propane see “Propane 
Conversion” on page 33 before 
proceeding.

1.   Install the secondary floor on 

the side away from the gas 
connections first.  

2.  Insert the wires leading from the 

secondary floor half through one 
of the grommets in the bulkhead 
plate. 

3.  On the bulkhead side, tilt the 

floor approximately 45 degrees 
and insert the wires from 
the floor through the rubber 
grommet in the bulkhead plate 
 (Figure 72). 

4.  Insert the pilot up through the 

pilot hole then lower and secure 
the secondary floor half in place. 

5.  Place the first burner as shown 

in Figure 73. Be sure to engage 
the venturi fully onto the orifice. 
Secure with single screw in 
burner support leg. Repeat with 
other burner. 

6.  Attach the pilot to the burner 

support leg as shown in Figure 
74. 

Figure 72:  Installing one half of secondary floor.

Figure 74:  Attaching pilot to burner leg.

100001140

36

TCWS54STOK_270619-56

Содержание D Series

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды