manualshive.com logo in svg

Town & Country Fireplaces D Series, Руководство по установке

Поделиться
Скачать
Town & Country Fireplaces D Series Скачать руководство пользователя страница 28

Figure 43:  ng04 Tray leg installation.

Figure 42:  ngo4 Secondary floor installation.

If converting to propane see conversion 
instructions on “Propane Conversion” 
on page 33 before proceeding.

1.  Install one side of the secondary floor as  
 

shown. Repeat with the other side but  

 

do not put in the two center screws until  

 

you put the center tray leg in place   

 

(Figure 42 and Figure 43).

2.  Attach tray legs as shown in Figure 43  
 

The center tray leg and the right side  

 

of the secondary floor are attached with  

 

the same screws to the center floor leg.

 

3.  Attach pilot to center tray leg (Figure 44)

ATTACH HERE AND ON OPPOSITE SIDE

ATTACH CENTER TRAY

LEG AND SECONDARY 

FLOOR TOGETHER

ROUTE PILOT UP 

THROUGH HERE

ROUTE PILOT UP 

THROUGH HERE

Installation:

Figure 44:  ng04 Pilot positioning.

100001140

28

TCWS54STOK_270619-56

Содержание D Series

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды