Toshiba TOSLINE-S20LP Скачать руководство пользователя

Страница: 51 / 66



TermSTS

Status

Meaning

00H

Normal complete

01H

• Occurs if a register other than XW, YW,W, LW, RW, D, F, T, C, or SW is

designated as the data storage register in one of the following requests.
Requests: Remote station loopback, Register read/write.

• In a register read or write request, the request designated a read or write from

a T register to a register other than a T register.
(This also applies to C registers.)

02H

Response timeout

• Occurs if a response is not received within the designated time for a remote

station loopback or register read/write request.

03H

Parameter error

• Occurs if a value other than 2 is designated for the module ID.

• Occurs if a value other than 1 (T2N/T3H) or 2 (T3H) is designated for the

channel number.

04H

• Occurs if an attempt to write is made when the remote registers were write

protected.

• Occurs if an attempt to read is made when the local registers were write

protected.

05H

(Reserved)
Module error

• Occurs if the module is down.

• Occurs if the master station of PC link times out

06H

Initialization in progress

• Occurs if the module is initializing.

07H

No send channel (CH)

• Occurs if the corresponding S20LP-station is not installed.

08H

Invalid station number

• Occurs if the local station address designated 0 or over 64.

• Occurs if the remote station address was set up the same local station

address.

09H

Transfer size error

• Occurs if either 0 or 129 or more words were designated for either a register

read/write or a remote station loopback request.

0AH

Boundary error

• Occurs if the specified area (start a register range) does not exist in

the T2N/T3H data storage registers.

Requests: Remote port loopback, Register read/write

0BH

Transmission error

• Occurs if the S20LP-station returns an error response.

Detailed information (the S20LP-station response status) is stored at B+1.

0CH

I/O no answer error

• Occurs if the T2N/T3H cannot access S20LP-station.

IC card designation error
(T3H)

• Occurs if an error occurs when the T3H IC card is being used as register

(expanded F register) in one of the following request.
(See the T3H Instruction Manual.)
Request: Register read/write
1. Occurs if IC card is not setting up.
2. IC card type error
3. Register write protected

0DH

(Reserved : T2N)

0EH

Retry timeout error

• Occurs if a T2N retransmission times out.

0FH

(Reserved)

Содержание TOSLINE-S20LP



































































Результаты поиска

Содержание TOSLINE-S20LP

Отзывы:

Похожие инструкции для TOSLINE-S20LP

Бренды по названию

Популярные бренды

Toshiba TOSLINE-S20LP, Инструкция по эксплуатации

Результаты поиска

Содержание TOSLINE-S20LP

Отзывы:

Похожие инструкции для TOSLINE-S20LP

Бренды по названию

Популярные бренды