Toshiba TOSLINE-S20LP страница 34 Скачать руководство пользователя

Страница: 34 / 66



5.2 Self-diagnostic function

The S20LP-station has the following self-diagnostic function.

•

At initialization (at power on)

Diagnostic item

Station operation abnormal

ROM BCC check

Station moves into Down mode.

RAM read/write check

Communications with other stations are

CPU and peripheral LSI check

not possible. This state will be reset by

Station number check

power off/on (SN325, T2N) or pressing

Reset switch (SN325).

Transmission parameter

(EEPROM) check

Station moves into Standby mode. In
this state, scan transmission is not
possible but message transmission is
available. Station waits for transmission
parameter setting.

•

During operation

Diagnostic item

Station operation abnormal

Watch dog timer check

Station moves into Down mode.

Abnormal timer check

(jabber timer) check

Communications with other stations are
not possible. This state will be reset by
power off/on (SN325, T2N) or pressing
Reset switch (SN325).

Receive frame check (CRC check)

Station ignores the abnormal frame.

Response check

In message transmission, if response
from the target station cannot be
received, station re-sends the frame.

No signal state check

If no signal state continues more than
specified time, station starts re-
configuration operation.

Содержание TOSLINE-S20LP



































































Результаты поиска

Содержание TOSLINE-S20LP

Отзывы:

Похожие инструкции для TOSLINE-S20LP

Бренды по названию

Популярные бренды

Toshiba TOSLINE-S20LP, Инструкция по эксплуатации

Результаты поиска

Содержание TOSLINE-S20LP

Отзывы:

Похожие инструкции для TOSLINE-S20LP

Бренды по названию

Популярные бренды