Toshiba TOSLINE-S20LP Скачать руководство пользователя | Manualshive

Страница: 10 / 66

background image



9



6

F

3

B

0

3

5

6

1.3 S-LS overview

The S-LS (TOSLINE-S20 Loader System) on a personal computer (PC) monitors station
conditions, reads/writes control data, and sets up parameters. The transmission parameters set by
S-LS is stored in the S20LP-station's built-in EEPROM.

Connection between S-LS and S20LP-station is made by an loader cable, that is the same cable
as for T-PDS.

The following are the details of the menu. Select an intended station in the Station Connection
Diagram window for display and specify the window in the menu or the toolbar.

[File]

[Display Scan Address List]

Displays the Scan Address List window.

[Display Station Down Information]

Displays Down Information when the local station is downed.

[Save Files All Station’s Information]

Saves the setup information of all stations in the file.

[Exit]

Terminates the application.

[Menu]

[Setting Information]

Displays the Setting Information window.

[Data Access]

Displays the Data Access window.

[RAS Information]

[Online Map]

Displays the Online Map window.

[Scan Healthy Map]

Displays the Scan Healthy Map window.

[Loop Map]

Displays the Loop Map window.

[Station Status]

Displays the Station Status window.

[Station Down Information]

Displays the Station Down Information.

[RAS Counter Information]

Displays the RAS Counter Information

[Online/Standby Request]

Displays the Online/Standby Request window.

[Test Request]

Displays the Test Request window.

[Option]

[Station Display Position]

[Registration]

Registers the display positions of the stations rearranged.

[Display]

Reflects the display positions of the registered stations in the window.

[Normal]

Displays the stations rearranged in the ascending order of smaller display

position numbers.

[Communication Environment Setting] Displays the Communication Environment Setting window.

[Window]

[Display Small Size]

Displays the Station Connection Diagram in small size.

[Help]

[Contents]

Displays the Help window.

[Key Word Search]

Displays the Retrieve window in Help.

[Version Information]

Displays the information of the application version.

«
...
8
9
10
11
12
...
»

Содержание TOSLINE-S20LP



































































Отзывы:

Нет отзывов

Похожие инструкции для TOSLINE-S20LP

ShareCenter DNS-320L

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 99

Бренд: D-Link Страницы: 5

Бренд: D-Link Страницы: 15

AirPro DWL-6000AP

Бренд: D-Link Страницы: 65

Бренд: D-Linke Страницы: 32

Бренд: Abocom Страницы: 1

Бренд: Datasat Страницы: 32

Бренд: C&H Technologies Страницы: 46

Бренд: Paradyne Страницы: 2

Бренд: Paradyne Страницы: 20

Бренд: Paradyne Страницы: 2

Бренд: Zhone Страницы: 2

Бренд: Oracle Страницы: 24

Бренд: TP-Link Страницы: 2

SRCSASBB8I - RAID Controller

Бренд: Intel Страницы: 36

Бренд: Qlogic Страницы: 2

Бренд: C-Data Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды