Toshiba TOSLINE-S20LP Скачать руководство пользователя

Страница: 35 / 66



5.3 LED indication

(1) SN325

The S20LP-station is equipped with STN, ONL and SCAN LEDs, which indicate the
station modes.

STN

ONL

SCAN

Station mode

Remarks

Lit

Online

Scan / Message transmission is enabled

Not lit

Online

Scan transmission is disabled Message
transmission is enabled

Lit

Not lit

Offline

Scan / Message transmission is disabled

Lit

Blink

Not lit

Standby

Transmission parameter is not written in
EEPROM.

Transmission information is standby start up.

Connection machines is abnormal.

T3H is not RUN mode.

Not lit

Blink

Down

Station number is illegal

(simultaneously)

Blink

Not lit

Down

Jabber timeout

Not lit

Down

Receive buffer is overflow.

Target cycle time is shortage.

Blink

Down

Watch dog timer error

(alternately)

(2) T2N

The S20LP-station is equipped with RUN and SONL LEDs, which indicate the station

modes.

SRUN

SONL

Station mode

Remarks

Lit

Online

Scan / Message transmission is enabled

Lit

Not lit

Offline

Scan / Message transmission is disabled

Lit

Blink

Standby

Transmission parameter is not written in EEPROM.

Transmission information is standby start up.

Connection machines is abnormal.

T2N is not RUN mode.

Not lit

Blink

Down

Station number is illegal.

Jabber timeout.

Watch dog timer error.

Not lit

Down

Receive buffer is overflow.

Target cycle time is shortage.

Содержание TOSLINE-S20LP



































































Результаты поиска

Содержание TOSLINE-S20LP

Отзывы:

Похожие инструкции для TOSLINE-S20LP

Бренды по названию

Популярные бренды

Toshiba TOSLINE-S20LP, Инструкция по эксплуатации

Результаты поиска

Содержание TOSLINE-S20LP

Отзывы:

Похожие инструкции для TOSLINE-S20LP

Бренды по названию

Популярные бренды