manualshive.com logo in svg

Toshiba Satellite P20-25 Series, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Satellite P20-25 Series Скачать руководство пользователя страница 76

2.16  Wireless LAN Troubleshooting 

2  Troubleshooting Procedures 

The wireless LAN antenna wire, wireless LAN unit or system board may each be the source of a 
wireless LAN fault. Any of these components may be damaged. To determine if the computer’s 
wireless LAN system is functioning properly, perform the following procedures. Figure 2-15 
outlines the process. Start with Procedure 1 and continue with the other procedures as instructed. 

Procedure 1:  Diagnostic test 
Procedure 2:  Connector and replacement check 

Procedure 1 

Diagnostic test 

Run the Diagnostic Program, which will automatically execute the wireless LAN test.  Refer to 
Chapter 3, Tests and Diagnostics for more information on the program. 
If an error is located, go to Procedure 2.  If an error is not located, the wireless LAN system is 
functioning properly.

 

 

Procedure 2 

Connector and replacement check 

The wireless LAN antenna, wireless LAN unit or system board may be disconnected or damaged.  
Disassemble the computer following the steps described in Chapter 4, 

Replacement Procedures

, 

and perform the following checks. 
 
Check 1 

Make sure that the wireless LAN antenna is firmly connected to the wireless LAN 
unit (refer to Chapter 4 for instructions) and that the wireless LAN unit is securely 
slotted into the system board. If the problem persists, go to Check 2. 

Check 2 

Check that the wireless communication switch is turned to “On”, then make sure that 
the wireless communication LED on the front panel is lit. If the LED is lit but the 
wireless LAN function is still faulty, the antenna may be damaged. Replace with a 
new antenna following the steps in Chapter 4, 

Replacement Procedures

. If the 

problem persists, or if the wireless LAN LED is not lit when the wireless 
communication switch is turned to “On”, go to Check 3. 

Check 3 

The wireless LAN unit may be damaged. Replace it with a new one following the 
instructions in Chapter 4. If the problem still exists, perform Check 4. 

Check 4 

The system board may be damaged.  Replace it with a new one following the 
instructions in Chapter 4.

Satellite P20-25 Series Maintenance Manual 

 

2-39 

Содержание Satellite P20-25 Series



























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды