manualshive.com logo in svg

Toshiba Satellite P20-25 Series, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Satellite P20-25 Series Скачать руководство пользователя страница 63

2  Troubleshooting Procedures  

2.10  TouchPad Troubleshooting

 

To determine if the computer’s built-in TouchPad is functioning properly, perform the following 
procedures. Figure 2-9 outlines the process. Start with Procedure 1 and continue as instructed. 

Procedure 1:  TouchPad connection check 
Procedure 2:  TouchPad replacement check 

Procedure 1 

TouchPad connection check 

The TouchPad is connected via the TouchPad FPC to the system board. Make sure the TouchPad 
FPC cable is firmly connected to the TouchPad and system board. Refer to Chapter 4, 

Replacement Procedures,

 for instructions on how to disassemble the computer and then perform 

the following checks. 

If any of the connections are loose, reconnect firmly.  If any of the connections is damaged, or 
there is still an error, go to Procedure 2. 

Procedure 2 

TouchPad replacement check 

The TouchPad unit or FPC may be defective or damaged.  Replace each with a new one 
following the steps in Chapter 4.  If the FDD is still not functioning properly, replace the system 
board with a new one following the steps in Chapter 4. 

 

2-26 

Satellite P20-25 Series Maintenance Manual 

Содержание Satellite P20-25 Series



























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды