manualshive.com logo in svg

Toshiba Satellite P20-25 Series, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Satellite P20-25 Series Скачать руководство пользователя страница 153

4  Replacement Procedures 

4.12  CPU 

Installing the CPU 

To install the CPU, follow the steps below and refer to the figures in the preceding 
section. 

 

CAUTION: 

If you remove the heat sink, you should use the CPU grease tool to remove 

the grease on the CPU and heat sink. Reapply fresh grease before installing the heat sink. 

 

1.  Make sure that the notch on the 

cam

 is aligned with the 

open

 position. 

2. Seat the 

CPU

 to align the triangle mark on the 

CPU

 with the one on the 

CPU socket

. 

Make sure the alignment is exact to avoid damaging pins on the 

CPU

. 

3. Press the 

CPU

 softly with your fingers and turn the 

cam

 on the 

CPU socket

 to the 

closed

 position with a flat-blade screwdriver to secure the 

CPU

. 

4. Seat the

 heat sink

 over the 

CPU

 and secure with four screws in the order indicated 

on the heat sink (1,2,3,4). 

5. Secure the

 CPU compartment cover

 with the 

five embedded security screws

. 

 

4-38 

Satellite P20-25 Series Maintenance Manual 

Содержание Satellite P20-25 Series



























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды