Toshiba Satellite P20-25 Series Скачать руководство пользователя страница 173

Страница: 173 / 250

4.19 Display Assembly

4 Replacement Procedures

Installing the Display Assembly

To install the display assembly, follow the steps below and refer to the figures in the
preceding section.

1. Seat the display assembly taking care not to crush to the

LCD display cable

wireless LAN antenna

2. Feed the

wireless LAN antenna

through the system board into the

wireless LAN

compartment

3. If a

wireless LAN card

is installed, remove the

wireless LAN compartment cover

and attach the ends of the

wireless LAN antenna

to the card. The

black antenna

cable

should be attached to the connector nearer the rear side of the computer, the

white antenna cable

to the connector closer to the front panel.

4. Secure the hinges with

two M2.5

6 screws

. Use the same screw to secure

the

display cable

to the left side hinge.

5. Attach the

display cable

to its connector on the

system board

6. Seat the

hinge cover

and secure its top-side with

one m2.5

12 screw

at the left end

and

one m2.5

3 silver screw

at the right end.

7. Secure the

hinge cover

with

one M2

4 screw

at the rear of the each hinge.

8. Secure the display assembly with two

M2.5

6 screws

on the

I/O cover

Satellite P20-25 Series Maintenance Manual

4-57

Содержание Satellite P20-25 Series



























































































































































































































































Результаты поиска

Содержание Satellite P20-25 Series

Отзывы:

Бренды по названию

Популярные бренды

Toshiba Satellite P20-25 Series, Руководство по обслуживанию

Результаты поиска

Содержание Satellite P20-25 Series

Отзывы:

Бренды по названию

Популярные бренды