Toshiba Satellite P20-25 Series Скачать руководство пользователя страница 143

Страница: 143 / 250

4 Replacement Procedures

4.9 Wireless LAN Unit

Installing the Wireless LAN Unit

To install the wireless LAN unit, follow the steps below and refer to the figures in the
preceding section.

1. Turn the computer upside down and loosen

two embedded screws

securing the

wireless LAN compartment cover

2. Lift off the

wireless LAN compartment cover

3. Fit the

wireless LAN unit’s

connectors into the computer’s connectors and press

carefully to ensure firm contact.

CAUTION

: Do not touch the connectors on the wireless LAN unit or on the

computer. Debris on the connectors may cause malfunction.

4. Gently, push the

wireless

LAN

unit

down until the

latches

engage the unit to hold it

in place.

5. Attach the ends of the

wireless LAN antenna

. The

black antenna cable

should be

attached to the connector nearer the rear side of the computer, the

white antenna

cable

to the connector closer to the front panel.

6. Seat the

wireless LAN compartment cover

and secure it with the

two embedded

screws

4-28

Satellite P20-25 Series Maintenance Manual

Содержание Satellite P20-25 Series



























































































































































































































































Результаты поиска

Содержание Satellite P20-25 Series

Отзывы:

Бренды по названию

Популярные бренды

Toshiba Satellite P20-25 Series, Руководство по обслуживанию

Результаты поиска

Содержание Satellite P20-25 Series

Отзывы:

Бренды по названию

Популярные бренды