manualshive.com logo in svg

Toshiba Satellite P20-25 Series, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Satellite P20-25 Series Скачать руководство пользователя страница 3

 

 

Satellite P20-25 Series Maintenance Manual 

 

iii 

Preface 

This maintenance manual describes how to perform hardware service maintenance for the 
Toshiba Personal Computer Satellite P20 Series, referred to as the P20-25 Series in this 
manual. 

The procedures described in this manual are intended to help service technicians isolate 
faulty Field Replaceable Units (FRUs) and replace them in the field. 

SAFETY PRECAUTIONS 

Four types of messages are used in this manual to bring important information to your 
attention.  Each of these messages will be italicized and identified as shown below. 

DANGER: 

“Danger” indicates the existence of a hazard that could result in death or 

serious bodily injury if the safety instruction is not observed. 

 

WARNING: 

“Warning” indicates the existence of a hazard that could result in bodily 

injury if the safety instruction is not observed. 

 

CAUTION:

  “Caution” indicates the existence of a hazard that could result in property 

damage if the safety instruction is not observed. 

 

NOTE:

  “Note” contains general information that relates to your safe maintenance 

service. 

 

Improper repair of the computer may result in safety hazards. Toshiba requires service 
technicians and authorized dealers or service providers to ensure the following safety 
precautions are adhered to strictly. 

 

Be sure to fasten screws securely with the right screwdriver. If a screw is not fully 
fastened, it could come loose, creating a danger of a short circuit, which could cause 
overheating, smoke or fire. 

 

If you replace the battery pack or RTC battery, be sure to use only the same model 
battery or an equivalent battery recommended by Toshiba. Installation of the wrong 
battery can cause the battery to explode. 

 

Содержание Satellite P20-25 Series



























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды