Toshiba OIS PLUS Series Скачать руководство пользователя страница 13

Страница: 13 / 131

Handling and Storage

•

Use proper lifting techniques when moving the OIS; including properly sizing up the

load, and getting assistance if required.

•

Store in a well-ventilated covered location and preferably in the original carton if the

equipment will not be used upon receipt.

•

Store in a cool, clean, and dry location. Avoid storage locations with extreme

temperatures, rapid temperature changes, high humidity, moisture, dust, corrosive

gases, or metal particles.

•

Do not store the unit in places that are exposed to outside weather conditions (i.e., wind,

rain, snow, etc.).

•

Store in an upright position as indicated on the shipping carton.

•

Include any other product-specific requirements.

Disposal

Never dispose of electrical components via incineration. Contact your state environmental

agency for details on disposal of electrical components and packaging in your area.

0.4 Installation Precautions

Location and Ambient Requirements

•

Adequate personnel working space and adequate illumination must be provided for

adjustment, inspection, and maintenance of the equipment (refer to NEC Article 110-

34).

•

Avoid installation in areas where vibration, heat, humidity, dust, fibers, steel particles,

explosive/corrosive mists or gases, or sources of electrical noise are present.

•

The installation location shall not be exposed to direct sunlight.

•

Allow proper clearance spaces for installation. Do not obstruct the ventilation openings.

Refer to the recommended minimum installation dimensions as shown on the enclosure

outline drawings.

•

The ambient operating temperature shall be between 0

and 50° C (32° and 122° F).

Mounting Requirements

•

Only

Qualified Personnel

should install this equipment.

•

Install the unit in a secure upright position in a well-ventilated area.

•

A noncombustible insulating floor or mat should be provided in the area immediately

surrounding the electrical system at the place where maintenance operations are to be

performed.

•

As a minimum, the installation of the equipment should conform to the NEC Article 110

Requirements For Electrical Installations, OSHA, as well as any other applicable

national, regional, or industry codes and standards.

•

Installation practices should conform to the latest revision of NFPA 70E Electrical Safety

Requirements for Employee Workplaces.

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Содержание OIS PLUS Series




































































































































Результаты поиска

Содержание OIS PLUS Series

Отзывы:

Похожие инструкции для OIS PLUS Series

Бренды по названию

Популярные бренды

Toshiba OIS PLUS Series, Руководство пользователя

Результаты поиска

Содержание OIS PLUS Series

Отзывы:

Похожие инструкции для OIS PLUS Series

Бренды по названию

Популярные бренды