Toshiba OIS PLUS Series Скачать руководство пользователя страница 15

Страница: 15 / 131

0.5 Connection, Protection & Setup

Personnel Protection

•

Installation, operation, and maintenance shall be performed by

Qualified

Personnel

Only

•

A thorough understanding of the OIS will be required before the installation, operation,

or maintenance of the OIS.

•

Rotating machinery and live conductors can be hazardous and shall not come into

contact with humans. Personnel should be protected from all rotating machinery and

electrical hazards at all times. Depending on its program, the OIS can initiate the start

and stop of rotating machinery.

•

Insulators, machine guards, and electrical safeguards may fail or be defeated by the

purposeful or inadvertent actions of workers. Insulators, machine guards, and electrical

safeguards are to be inspected (and tested where possible) at installation and

periodically after installation for potential hazardous conditions.

•

Do not allow personnel near rotating machinery. Warning signs to this effect shall be

posted at or near the machinery.

•

Do not allow personnel near electrical conductors. Human contact with electrical

conductors can be fatal. Warning signs to this effect shall be posted at or near the

hazard.

•

Personal protection equipment shall be provided and used to protect employees from

any hazards inherent to system operation or maintenance.

System Setup Requirements

•

When using the OIS as an integral part of a larger system, it is the responsibility of the

OIS installer or maintenance personnel to ensure that there is a fail-safe in place (i.e.,

an arrangement designed to switch the system to a safe condition if there is a fault or

failure).

•

System safety features should be employed and designed into the integrated system in

a manner such that system operation, even in the event of system failure, will not cause

harm or result in personnel injury or system damage (i.e., E-Off, Auto-Restart settings,

System Interlocks, etc.).

•

The programming setup and system configuration of the OIS may allow it to start a

motor unexpectedly. A familiarity with Auto-restart settings is a requirement to use this

product.

•

Improperly designed or improperly installed system interlocks may render the motor

unable to start or stop on command.

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Содержание OIS PLUS Series




































































































































Результаты поиска

Содержание OIS PLUS Series

Отзывы:

Похожие инструкции для OIS PLUS Series

Бренды по названию

Популярные бренды

Toshiba OIS PLUS Series, Руководство пользователя

Результаты поиска

Содержание OIS PLUS Series

Отзывы:

Похожие инструкции для OIS PLUS Series

Бренды по названию

Популярные бренды