manualshive.com logo in svg

Toro Z Master 4000 Series, Руководство по обслуживанию, Страница: 59 / 114

Поделиться
Скачать
Toro Z Master 4000 Series Скачать руководство пользователя страница 59

Seat Removal (continued)

g346225

Figure 36

7. With assistance, lift the seat pan/seat assembly away from the machine.

8. Remove the 4 (5/16 inch) locks securing the seat pan to the seat assembly.

Seat Installation

1. Install and tighten the 4 (5/16 inch) lock nuts securing the seat pan to the

seat assembly.

2. With assistance, install the seat pan/seat assembly into the machine.

3. Connect the seat switch to the seat. With assistance, slide the seat pan/seat

assembly forward and tip upwards to gain access to the seat switch
connector.

g346225

Figure 37

4. Install the 2 (5/16 inch) torx screws securing the seat pan to the chassis.

5. Install the 2 (5/16 inch) torx screws securing the front tank retainer plate

to the seat pan.

4000 Series Z MASTER® Service Manual

Page 5–19

Chassis: Service and Repairs

3442-427 Rev A

 

Содержание Z Master 4000 Series



















































































































Отзывы:

Нет отзывов