manualshive.com logo in svg

Toro Z Master 4000 Series, Руководство по обслуживанию, Страница: 54 / 114

Поделиться
Скачать
Toro Z Master 4000 Series Скачать руководство пользователя страница 54

Left Console Removal (continued)

g346223

Figure 28

4. Disconnect the wiring harness from the USB charger.

5. Remove the 2 (5/16 inch) lock nuts and carriage bolts securing the LH

console to the chassis.

6. Lift the LH console away from the machine.

Left Console Installation

1. Install the LH console onto the machine.

2. Install and tighten the 2 (5/16 inch) lock nuts and carriage bolts securing the

LH console to the chassis.

3. Connect the wiring harness to the USB charger.

4. Install the LH side pod to the LH console. Install the 4 (1/4-20 inch) torx

screws securing the LH side pod to the LH console.

Note:

3 screws are shown in the image below.

g346223

Figure 29

5. Connect the battery by installing the positive cable first, then the negative

cable to the battery.

Chassis: Service and Repairs

Page 5–14

4000 Series Z MASTER® Service Manual

3442-427 Rev A

 

Содержание Z Master 4000 Series



















































































































Отзывы:

Нет отзывов