manualshive.com logo in svg

Toro GrandStand TURBO FORCE 74513, Руководство оператора

Поделиться
Скачать
Toro GrandStand TURBO FORCE 74513 Скачать руководство пользователя страница 4

Safety

This machine has been designed in accordance with
ANSI B71.4-2017.

General Safety

This product is capable of amputating hands and
feet and of throwing objects. Always follow all safety
instructions to avoid serious personal injury.

•

Read and understand the contents of this

Operator’s Manual

before starting the engine.

•

Do not put your hands or feet near moving
components of the machine.

•

Do not operate the machine without all guards
and other safety protective devices in place and
functioning properly on the machine.

•

Keep clear of the discharge opening.

•

Keep bystanders and children out of the operating
area. Do not allow children to operate the machine.
Allow only people who are responsible, trained,
familiar with the instructions, and physically
capable to operate the machine.

•

Stop the machine, shut off the engine, and remove
the ignition key before servicing, fueling, or
unclogging the machine.

Improperly using or maintaining this machine can
result in injury. To reduce the potential for injury,
comply with these safety instructions and always
pay attention to the safety-alert symbol

, which

means Caution, Warning, or Danger—personal safety
instruction. Failure to comply with these instructions
may result in personal injury or death.

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.

decalbatterysymbols

Battery Symbols

Some or all of these symbols are on your battery.

1.

Explosion hazard

6.

Keep bystanders away.

2.

No fire, open flames, or
smoking

7.

Wear eye
protection—explosive
gases can cause blindness
and other injuries.

3.

Caustic liquid/chemical
burn hazard

8.

Battery acid can cause
severe burns.

4.

Wear eye protection.

9.

Flush eyes immediately
with water and get medical
help fast.

5.

Read the

Operator’s

Manual

.

10.

Contains lead; do not
discard.

decaloemmarkt

Manufacturer's Mark

1.

This mark indicates that the blade is identified as a part
from the original machine manufacturer.

decal93-7818

93-7818

1.

Warning—read the

Operator's Manual

for instructions on

torquing the blade bolt/nut to 115 to 149 N∙m (85 to 110
ft-lb).

decal106-5517

106-5517

1.

Warning—do not touch the hot surface.

4

 

Содержание GrandStand TURBO FORCE 74513





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды