manualshive.com logo in svg

Toro GrandStand TURBO FORCE 74513, Руководство оператора

Поделиться
Скачать
Toro GrandStand TURBO FORCE 74513 Скачать руководство пользователя страница 37

Charging the Battery

WARNING

Charging the battery produces gasses that
can explode.

Never smoke near the battery and keep sparks
and flames away from battery.

Important:

Always keep the battery fully charged

(1.265 specific gravity) to prevent battery damage
when the temperature is below 0°C (32°F).

1.

Remove the battery from the chassis; refer to

Removing the Battery (page 36)

.

2.

Check the electrolyte level.

3.

Ensure that the filler caps are installed on the
battery.

4.

Charge the battery for 1 hour at 25 to 30 A or 6
hours at 4 to 6 A.

5.

When the battery is fully charged, unplug the
charger from the electrical outlet, and disconnect
the charger leads from the battery posts (

Figure

50

).

6.

Install the battery onto the machine and connect
the battery cables; refer to

Installing the Battery

(page 37)

.

Note:

Do not run the machine with the battery

disconnected; electrical damage may occur.

g000538

Figure 50

1.

Positive battery post

3.

Red (+) charger lead

2.

Negative battery post

4.

Black (-) charger lead

Installing the Battery

Install the battery as shown in

Figure 51

.

g030989

Figure 51

37

 

Содержание GrandStand TURBO FORCE 74513





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды