Toro 30488 Скачать руководство пользователя страница 8

Страница: 8 / 60

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area of potential
danger. Replace any decal that is damaged or lost.

Manufacturer's Mark

Indicates the blade is identified as a part from the original
machine manufacturer.

93-7010

Thrown object hazard—keep bystanders a safe distance
from the machine.

Thrown object hazard, mower—keep the deflector in place.

Cutting/dismemberment of hand or foot—stay away from
moving parts.

93-7818

Warning—read the

Operator's Manual

for instructions on

torquing the blade bolt/nut to 115-149 N-m (85-110 ft-lb).

93-7828

Thrown object hazard, mower—keep the deflector in place.

Cutting/dismemberment of hand or foot—stay away from
moving parts.

104-8186

48 inch mower

106-5517

Warning—do not touch the hot surface.

112-8721

Parking brake—off

Parking brake—on

Содержание 30488





























































Результаты поиска

Содержание 30488

Отзывы:

Похожие инструкции для 30488

Бренды по названию

Популярные бренды

Toro 30488, Руководство оператора

Результаты поиска

Содержание 30488

Отзывы:

Похожие инструкции для 30488

Бренды по названию

Популярные бренды