background image

24 

11. External receiver (optional) 

The 

RED

 wire of the external receiver 

should be connected into the “#11” terminal. 

The 

BLACK

 wire of the external receiver 

should be connected into the “#5” terminal. 

The 

BROWN

 wire of the external receiver 

should be connected into the “#4” terminal. 

Note: Using of the exit wand, keypad and external receiver would cause the battery exhausted quickly. 

Big  capacity  of  battery  and  big  power  of  solar  panel  (if  the  solar  panel  is  used  as  main  charger)  is 

required if you want to use either of them. 

How to Program the Remote to the Opener 

 

The  remote  MUST  be  programed  to  the  opener  BEFORE  OPERATING.  Please  follow  the  steps  to 

program the remote. 

 

Activate the opener only when gate is in full view, free of obstruction and properly adjusted. No one 

should enter or leave gate area while gate is in motion. DO NOT ALLOW CHILDREN to operate push 

button or remote. DO NOT ALLOW CHILDREN TO PLAY NEAR THE GATE. 

 

If you purchase additional remote controls, the gate opener must be programmed to accept the new 

remote code. 

 

If you lose one of any remote control, please erase and reprogram all other remote controls to have a 

new code for safety. 

Press and release the 

CODE SW

 button, the 

CODE

 LED will be ON

,

 then press the key on the remote 

two 

times

  in  2  seconds, 

between  the  two  times  HOLD  ON  FOR  A  MOMENT

,  the 

CODE

  LED  will  flash  for  3 

seconds and then to OFF. Now the remote has been programmed successfully. 

 

 

NOTE:

 

Max. 8 remotes can be programmed for the opener. An External Receiver (optional) allows up to 

250pcs  remotes  to  be  programmed  for  the  opener.  TOPENS  ERM12  Universal  External  Receiver  is 

available at TOPENS Store.   

 

TOPENS  ERM12  Universal  External  Receiver  is  also  compatible  with  other  brand  swing  gate  opener, 

sliding gate opener and garage door opener. 

 

How to Erase All the Remote Codes 

Press and hold the 

CODE SW

 button until the 

CODE

 LED from ON to OFF. Now all remote codes have been 

erased. 

How to Use the Remote to Operate Your Gate Opener 

Each remote has four buttons, from top to bottom are separately A, B, C and D. You may use this remote to 

Содержание A3132




































Отзывы: