Tonghui Electronics TH9110 Скачать руководство пользователя страница 33

Страница: 33 / 84

◇

Figure 4-18.4 OSC Test Interface

Figure 4-18.5 PAUSE Mode Interface

4.4.1OFFSET

Before testing, due to the change of working environment and position of the test cable, there may

be some base numbers when the tester is in no-load test. For some customers who pursuing accurate

measurement can conduct offset in TEST interface. The specific steps are as follows:

Remove the DUT from the test cable or fixture first and then set up the test conditions in the SETUP

interface.

Press

〖

TEST

〗

key to enter TEST interface, press F1 to offset. The tester starts to measure the

leakage current of the test cable and display the current, use the present test value as the zero value.

After pressing F1 offset key, the DANGER indicator flashes and the voltage output time is 5S.

(When the set test time is larger than 5S, if the time is less than 5S, the output voltage time is

according to the set test time.)

4.4.2 List Display and Step Display

In addition to the original step display interface, this tester also adds a list display interface, which

can display multi-step parameters. In the tester TEST interface, press the F6 key to switch the

interfaces.

系
统
设
置
中
测
试
相
关
参
数
设
置
如
图

4-2

所
示

系
统
设
置
中
测
试
相
关
参
数
设
置
如
图

4-2

所
示

系

统

设

系
统
设
置
中
测
试
相
关
参
数
设
置
如
图

4-2

所
示

系
统
设
置
中
测
试
相
关
参
数
设
置
如
图

4-2

所
示

系
统
设
置
中
测
试
相
关
参
数
设
置
如
图

4-2

所
示

系
统
设
置
中
测
试
相
关
参
数
设
置
如
图

系

统

设

系
统
设
置
中
测
试
相
关
参
数
设
置
如
图

4-2

所
示

系
统
设
置
中
测
试

Содержание TH9110





















































































Результаты поиска

Содержание TH9110

Отзывы:

Бренды по названию

Популярные бренды

Tonghui Electronics TH9110, Руководство по эксплуатации

Результаты поиска

Содержание TH9110

Отзывы:

Бренды по названию

Популярные бренды