Tone TOUCH 02 Скачать руководство пользователя

Страница: 7 / 30

Electrical connection

WARNING:

The brewer must be disconnected from the power source until specified in INITIAL SET-UP.

CAUTION

– Improper electrical installation will damage electronic components. Damage caused by incorrect elec-

trical connections is not covered by warranty.

An electrician must provide electrical service as specified in conformance with all local, state and federal electrical

codes.

Use a voltmeter to check the voltage and color coding of each conductor at the electrical source.

For models without a cord, remove the rear top cover then the rear panel and feed the cord through the strain

relief. Connect cord to the terminal block as indicated in the appropriate diagram above.

Ensure power switch on rear of brewer is in the off position. Connect brewer to power source and verify

voltage at terminal block. Replace rear panel and top cover.

If plumbing has been hooked up, brewer is ready for Initial Set-Up. If not, disconnect brewer from power

source.

WARNING:

Electrical connections must be made as specified above. Failure to follow these instructions can result

in personal injury, property or equipment damage.

NOTE:

This electrical service consist of 2 current carrying conductors (L1 and Neutral) and a separate

conductor for earth ground.

WARNING:

Before servicing or opening this device make sure the brewer is disconnected from power by

pulling its plug. The service technician has to see the pulled plug during the whole service operation.

BLACK NEUTRAL GREEN/

L1 N YELLOW

Содержание TOUCH 02































Результаты поиска

Содержание TOUCH 02

Отзывы:

Похожие инструкции для TOUCH 02

Бренды по названию

Популярные бренды

Tone TOUCH 02, Оригинальное руководство пользователя

Результаты поиска

Содержание TOUCH 02

Отзывы:

Похожие инструкции для TOUCH 02

Бренды по названию

Популярные бренды