Tomy SX-300E Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 60

background image

ー 16 ー

3-1. Method of movement and installation

3. INSTALLATION

WARNING

Do not install the autoclave in places where

chemicals such as flammable or corrosive

gases are stored.

●

Contravention is dangerous with likelihood of fire

or electric leakage and shock due to corrosion of

electrical parts.

Do not install the autoclave in a dusty or wet

place.

●

Contravention is dangerous with likelihood of short

circuit or ignition of electrical parts.

Do not install the autoclave near a sink or water pipe or any place

where spillage of water is likely.

●

Contravention is dangerous with likelihood of electric leakage or shock.

Install the SX-E Autoclave on a firm and level surface such as

a concrete floor that is capable of supporting the weight of the

autoclave.

●

Contravention is dangerous with likelihood of injury or physical damage

should the autoclave fall.

Support the autoclave with both hands and

move it gently.

①

<

Method of movement and installation

>

«
...
15
16
17
18
19
...
»

Содержание SX-300E





























































Отзывы:

Нет отзывов

Похожие инструкции для SX-300E

Бренд: Calistair Страницы: 44

Бренд: ZOLL Страницы: 5

Бренд: Accu-Chek Страницы: 3

Бренд: iBin Страницы: 2

Бренд: 3M Страницы: 2

Бренд: A.MENARINI Страницы: 2

Бренд: Warehouse-lighting Страницы: 3

Бренд: E2S Страницы: 5

Growers Supply 109722

Бренд: FarmTek Страницы: 9

Бренд: Gebhardt Anlagentechnik Страницы: 152

Бренд: Hach Страницы: 58

Бренд: Hach Страницы: 52

Бренд: IBEX Страницы: 4

Бренд: JBSYSTEMS Light Страницы: 17

Бренд: Olympus Страницы: 130

bionic power knee

Бренд: Össur Страницы: 2

BALANCE KNEE OM8

Бренд: Össur Страницы: 36

Бренд: Össur Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды