Tomy SX-300E Скачать руководство пользователя страница 19

Страница: 19 / 60

ー 18 ー

3-2. Power supply connection and protective grounding (earthing)

WARNING

Connect the power plug singly to the specified

power supply.

●

Contravention is dangerous with likelihood of fire,

electric leakage, or breakdown due to ignition.

Do not use power cable extensions.

●

Contravention is dangerous with likelihood of fire,

electric leakage, or breakdown due to ignition.

Be sure to provide protective grounding.

●

Contravention is dangerous with likelihood of

explosion, electric shock, or malfunction.

Do not use a gas pipe or water pipe etc. for

protective grounding.

●

Contravention is dangerous with likelihood of

explosion, electric shock, or malfunction.

For protection against electrical shock, grounding is required. When this type of grounding cannot

be provided, request works to be carried out by specialists.

Provide a power supply terminal board with the satisfying the condition given below and carry

out connection.

Power supply condition:

Protection against electrical shock is provided by connecting the protective grounding wire to the

grounding terminal.

※

Turn OFF the breaker to which the power cable is connected when hearing thunder in order to

prevent lightning damage.

SX-300E :

SX-500E :

SX-700E :

single-phase 230V AC (50/60 Hz), 10A or more

single-phase 230V AC (50/60 Hz), 15A or more

Содержание SX-300E





























































Результаты поиска

Содержание SX-300E

Отзывы:

Похожие инструкции для SX-300E

Бренды по названию

Популярные бренды

Tomy SX-300E, Руководство оператора

Результаты поиска

Содержание SX-300E

Отзывы:

Похожие инструкции для SX-300E

Бренды по названию

Популярные бренды